manualshive.com logo in svg

Kimberly-Clark M1000, Руководство оператора, Страница: 41 / 56

Поделиться
Скачать
Kimberly-Clark M1000 Скачать руководство пользователя страница 41

Alarm/ 

Alert 

Message
Displayed

Alarm/Alert

Description

System Status

Action

Water res-
ervoir level 
empty. Fill 
reservoir. 

Alarm

Reservoir is 
empty. 

Changes to Stop 
Mode.  
Audio alarm half-
second tone every  
10 seconds. Alarm/ 
Alert indicator 
flashing.

If connected to pads, purge pads. 
Fill Reservoir.

•
•

Purge not 
complete.
Pads may 
contain
extra water.

Alarm

A significant 
amount of water 
was still being 
returned from the 
pads at the end of 
the purge cycle.

Remains in Stop 
Mode (at end of 
purge). Audio 
alarm half-second 
tone every 2 min-
utes. Alarm indica-
tor flashing.

Pads may contain a significant amount of water. 
Use caution when removing pads from machine to 
avoid spilling water.
Machine may have been overfilled. Check level.
May indicate a machine malfunction, contact  
Clinical/Biomedical Engineering or Kimberly-Clark 
Service if problem persists and the reservoir is not 
overfilled.

•
•

•
•

System 
warming  
and Patient 
Temperature 
1 high.

Alarm

Patient 
Temperature  
1 reading is above 
38°C (100.4ºF), 
water temperature 
is above 38°C 
(100.4ºF) and sys-
tem is unable to 
cool in Automatic 
Mode.

Changes to Stop 
Mode. Audio alarm 
half-second tone 
every 2 minutes. 
Alarm indicator 
flashing. 

Verify patient temperature from another source.
Press Automatic Mode and observe water  
temperature to see if it has started to cool. 
Check that the vents on the sides of the machine 
are not blocked. 
If water temperature does not decrease, turn  
system off and allow to system to cool. 
Restart Automatic Mode. 
If water temperature does not fall in response  
to patient temperature, shut system off and call 
Kimberly-Clark Service.

•
•

•

•

•
•

Patient 
Temperature
1 above user-
defined limit.

Alert

Patient 
Temperature
1 reading is equal 
to or greater than 
the user-defined 
value established 
in the custom  
settings menu

Current Mode  
continues. Audio 
alarm half-second 
tone every  
2 minutes. Alarm/
Alert indicator 
flashing.

Check patient temperature.
Cancel alert.
If system stopped, alert will re-appear.
Adjust Patient High Temperature Alert in the  
custom menu, if desired.

•
•
•
•

System
cooling  
and Patient 
Temperature 
1 low.

Alarm

Patient 
Temperature  
1 reading is below 
32°C (89.6ºF), 
water temperature 
is below 32°C 
(89.6ºF) and the 
system is unable to 
heat in Automatic 
Mode

Changes to Stop 
Mode. Audio alarm 
half-second tone 
every 10 seconds. 
Alarm/Alert  
indicator flashing. 

Operate the system in manual mode with a set 
point above room temperature. 
When set point temperature has been reached, 
press Automatic Mode and observe water  
temperature to see if it has started to warm. 
Verify patient temperature from another source.
Turn system off. 
Restart Automatic Mode. 
If water temperature does not rise in response 
to patient temperature, shut system off and call 
Kimberly-Clark Service.

•

•

•
•
•
•

Patient 
Temperature 
1 below user- 
defined limit

Alert

Patient 
Temperature  
1 reading is equal  
or less than the 
user-defined value 
established in the 
custom settings 
menu. 

Current Mode  
continues. Audio 
alarm half-second 
tone every  
2 minutes. Alarm/
Alert indicator 
flashing.

Check patient temperature.
Cancel alert.
If system stopped, alert will re-appear.
Adjust Patient Low Temperature Alert in the cus-
tom menu, if desired. 

•
•
•
•

40

K

imberly

-c

larK

* Patient Warming Systems 

M000 Control Unit Operator’s Manual: U .S .

07

08

09

10

11

Appendix C — Alarm/Alert Table

06

Содержание M1000

























































Отзывы:

Нет отзывов