Kikusui TOS5300 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 77

Kikusui TOS5300 Скачать руководство пользователя страница 2

2

TOS5300_INTERFACE

Thank you for purchasing the TOS5300 Series Withstanding
Voltage and Insulation Resistance Tester.

There are five TOS5300 Series Manuals listed as follows.

■

Setup Guide

This manual is intended for first-time users of this product. It
provides an overview of the product and notes on usage. It also
explains how to set up the product for testing the DUT. Always
read this manual before using the product.

■

Quick Reference

This manual explains Panel description and operation briefly.

■

Safety Information

This document contains general safety precautions for this
product. Keep them in mind and make sure to observe them.

■

User’s Manual (PDF)

This manual is intended for first-time users of this product. It
provides an overview of the product and notes on usage. It also
explains how to configure the product, operate the product,
perform maintenance on the product, and so on.

■

Communication Interface Manual
(this manual, PDF)

This manual contains details about remotely controlling the
tester using SCPI commands.
The interface manual is written for readers with sufficient basic
knowledge of how to control measuring instruments using a
PC.

PDF files are included in the accompanying CD-ROM.
You can view the PDF files using Adobe Reader.

The newest version of the operation manual can be downloaded
from Download service of Kikusui website.

TOS5300 Series Manuals are intended for users of the
Withstanding Voltage and Insulation Resistance Tester and their
instructors. Explanations are given under the presumption that
the reader has knowledge about the electrical aspects of electrical
safety testing.

Product firmware versions

This manual applies to products with ROM versions 1.2X.

When contacting us about the product, please provide us with:

The model (marked in the top section of the front panel)
The ROM version (see the user’s manual)
The serial number (marked in the bottom section of the rear
panel)

Before reading this manual

First read the User’s Manual, which includes information on the
product’s hardware, to avoid connecting or operating the product
incorrectly.

Trademarks

Microsoft, Windows, and Visual Basic are registered trademarks of
Microsoft Corporation in the United States and/or other countries.

All company names and product names used in this manual are
trademarks or registered trademarks of their respective
companies.

Copyrights

The contents of this manual may not be reproduced, in whole or in
part, without the prior consent of the copyright holder.

The specifications of this product and the contents of this manual
are subject to change without prior notice.

© 2010 Kikusui Electronics Corporation

• The TOS5300 Series Withstanding Voltage and Insulation

Resistance Tester is also referred to as the TOS5300 Series.

• Device under test is also referred to as DUT.

• The term “PC” is used to refer generally to both personal

computers and workstations.

• The following markings are used in the explanations in the text.

Indicates information that you should know.

Indicates a reference to detailed information.

>

Indicates menu settings that you select. The menu item to the
left of the > symbol is a higher-level menu.

Indicates a feature or message that is only available on the
TOS5300 model.

Indicates a feature or message that is only available on the
TOS5301 model.

Indicates a feature or message that is only available on the
TOS5302 model.

Indicates a feature or message that is only available on the
TOS5302 model.

About the Operation Manuals

Notations Used in This Manual

See

5300

5301

5302

Memo

«
1
2
3
4
...
»

Содержание TOS5300














































































Отзывы:

Нет отзывов