Kikusui TOS5300 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 77

Kikusui TOS5300 Скачать руководство пользователя страница 11

TOS5300_INTERFACE

11

Message Overview

2

M

e

ssage O

v

e

rview

Example:

SYSTem:CONFigure:BEEPer:VOLume:FAIL MINimum;PASS MINimum

This compound command sends the same commands as the two following commands.

SYSTem:CONFigure:BEEPer:VOLume:FAIL MINimum
SYSTem:CONFigure:BEEPer:VOLume:PASS MINimum

In the first command (SYSTem:CONFigure:BEEPer:VOLume:FAIL), SYSTem:CONFigure:BEEPer:
VOLume is set as the path. Therefore, in the second command, SYSTem:CONFigure:BEEPer:VOLume
can be omitted.

If you specify a node that is not defined in the current path (except for FAIL and PASS), an error will
occur.

•

Program headers are separated by colons.

•

By using colons and semicolons, you can concatenate commands of different subsystems.

Example:

SENSe:JUDGment MINimum;:SOURce:VOLTage?

There are two root nodes in this compound command: SENSe and SOURce.

When the second command or later begins with a colon, the path that was specified by the
previous command is cleared.

•

The maximum length of a command that you can transmit on a single line is 128 bytes.

Special symbols and characters

The special symbols and characters that are used in this manual for the SCPI command syntax are
explained below.

Queries

You can query the settings and status of the TOS5300 Series.

To make a query, append a question mark to the end of the program header section. If the query
has parameters, insert a space after the question mark, and then write the parameters.

Example:

VOLTage? MINimum

Symbol or character

Description

< >

Character strings inside the < and > symbols indicate program data.
Do not include the < and > symbols in the actual program.

{ }

Characters and numbers delimited by “|” inside the { and } symbols indicate that
one of the delimited items is to be selected.Do not include the { and } symbols in
the actual program.

[ ]

Character strings inside [ and ] indicate optional data.
When optional data is not sent with the program, the default value is sent. Do not
include the [ and ] symbols in the actual program.

If you want to send two queries on separate lines, send the second query after you have received
the response to the first one. If you send query commands on two lines at the same time, you may
receive an incomplete response.

«
...
9
10
11
12
13
...
»

Содержание TOS5300














































































Отзывы:

Нет отзывов