Kikusui TOS5300 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 77

Kikusui TOS5300 Скачать руководство пользователя страница 18

18

TOS5300_INTERFACE

IEEE 488.2 Common Commands

*OPC

IEEE 488.2-1992, section
10.18

Sets the OPC bit (bit 0) of the event status register when all the commands that are in standby have
been processed.

Command

*OPC
*OPC?

Response

Returns “1” when all the commands that are in standby have been processed.

*OPT

Queries the options that are installed in the TOS5300 Series. This command performs the same
function as the SYSTem:OPTion? command.

Command

*OPT?

Response

Returns “0” if no options are installed. Returns one of the following responses in <character>
format if options are installed.
Returns “RC0X-TOS” if an RC01-TOS, RC02-TOS, HP01A-TOS, or HP02A-TOS option is installed.
Returns “SIGNAL I/O” if a SIGNAL I/O option is installed.

Example

If the RC01-TOS is installed,

this command returns

"RC0X-TOS."

*PSC

IEEE 488.2-1992, section
10.25

Sets whether the event status enable register and service request enable register are
cleared when the POWER switch is turned on.

Command

*PSC <NR1>
*PSC?

Parameter

Value:

0

When the POWER switch is turned on, the *ESE and *SRE settings are not
cleared.

1

When the POWER switch is turned on, the *ESE and *SRE settings are
cleared.

An SCPI error (-222, “Data out of range”) occurs if the specified value is outside the

range.

Example

To enable the power-on SRQ feature:

*PSC 0;*SRE 32;*ESE 128

Response

Returns the power-on status setting in response to the PSC? query.

*RCL

Aborts the test execution (operation) and loads the settings that have been saved to memory.

For the commands that are affected by *RCL, see ”Default State”.

Command

*RCL <NR1>

Parameter

Value:

1 to 3

Memory number

An SCPI error (-222, “Data out of range”) occurs if the specified value is outside the

range.

See

See

See

«
...
16
17
18
19
20
...
»

Содержание TOS5300














































































Отзывы:

Нет отзывов