Keysight N5990A-155 Скачать руководство пользователя страница 33

Страница: 33 / 106

Keysight N5990A-155 DisplayPort User Guide

Calibration and Test Procedures

Table 4

DisplayPort Sequencer Parameters

Common Parameters

The common parameters are used for several related calibration or test

procedures. They are displayed on the right side of the ValiFrame user

interface. They appear when the selected entry of the procedure tree on

the left is a group instead of an individual procedure.

The DisplayPort Receiver Test Software has some group parameters (in

addition to “Repetitions”) on the top-level entry of the procedure tree as

shown in

Table 5

. These parameters are common for all ValiFrame

procedures.

Parameter Name

Description

Procedure Error Case Behavior

•

Proceed With Next Procedure—if an error occurs in the current test or calibration procedure, continue
by running the next procedure in the sequence.

•

Abort Sequence—Abort the further running of the sequence.

Procedure Failed Case Behavior

•

Proceed With Next Procedure—if the current test or calibration procedure fails, continue by running
the next procedure in the sequence.

•

Abort Sequence—Abort the further running of the sequence.

Repetitions

The number of times the group or procedure will be repeated. If the value is '0', it runs only once.

Содержание N5990A-155











































































































Результаты поиска

Содержание N5990A-155

Отзывы:

Похожие инструкции для N5990A-155

Бренды по названию

Популярные бренды

Keysight N5990A-155, Руководство пользователя

Результаты поиска

Содержание N5990A-155

Отзывы:

Похожие инструкции для N5990A-155

Бренды по названию

Популярные бренды