Keysight N5990A-155 Скачать руководство пользователя страница 21

Страница: 21 / 106

Keysight N5990A-155 DisplayPort User Guide

ValiFrame DisplayPort Station

Table 1

DUT Parameter list

Sink PHY Test Parameters

This configuration appears when the option

DP Sink

is selected as the

Product Type

. There are two parameter groups, which offer different

possibilities for running the test and calibrations:
• Basic parameters, such as the data rates supported by the DUT. See

Figure 8

Parameter name

Description

Product
Parameters

Product Number

Name of the product.

Serial Number

Serial number of the product.

Port Name

Select a port number between 1 and 10.

Product Type

The Product type can be chosen as:

•

DP Sink: PC Monitors

•

eDP Sink: Embedded Sink

Description

Description of the product.

CTS Version

The selected CTS version defines the calibrations and tests according to the DisplayPort CTS revision.
The available version options are:

•

DP 1.4a

•

DP Type-C

Number of Lanes

DUTs with 1, 2 or 4 lanes can be tested.

Test Parameters

User Name

User name text field.

Comment

Text file for user comments.

Initial Start Date

Time stamp of the start of the current session.

Last Test Date

Time stamp of the last test conducted in the current session.

Compliance Mode

Test are conducted as mandated by the CTS. The parameters that are shown in the calibrations and test procedures cannot be
modified by the user.

Expert Mode

Calibration and tests can be conducted beyond the limits and constrains of the CTS. The parameters that are shown in the
calibrations and test procedures can be modified by the user.

Содержание N5990A-155











































































































Результаты поиска

Содержание N5990A-155

Отзывы:

Похожие инструкции для N5990A-155

Бренды по названию

Популярные бренды

Keysight N5990A-155, Руководство пользователя

Результаты поиска

Содержание N5990A-155

Отзывы:

Похожие инструкции для N5990A-155

Бренды по названию

Популярные бренды