Keysight N5990A-155 Скачать руководство пользователя страница 87

Страница: 87 / 106

Keysight N5990A-155 DisplayPort User Guide

Sink Calibration Procedures

Jitter Tolerance Characterization Test

Purpose and Method

This procedure tests the jitter tolerance of a device for different sinusoidal

jitter frequencies. It is only available after configuring the product in

“Expert Mode”.

For each sinusoidal jitter frequency, this procedure tries to find the jitter

amplitude at which the target BER can be sustained. It starts by setting

the maximum jitter amplitude. Then, the value is decreased using either

binary or linear search algorithm. The range of jitter frequencies to be

tested can be defined in the “Swept SJ frequency” parameters section.

The result is a curve that shows the maximum jitter that the DUT can

tolerate as a function of the SJ frequency.

Because the limitations of the instruments and the setup have influence on

the result (for example, if the DUT would tolerate higher jitter amplitudes

than the generator could apply), the maximum possible (or applied) jitter is

also reported.

Connection Diagram

Figure 37

Connection Diagram for Receiver Tests

Содержание N5990A-155











































































































Результаты поиска

Содержание N5990A-155

Отзывы:

Похожие инструкции для N5990A-155

Бренды по названию

Популярные бренды

Keysight N5990A-155, Руководство пользователя

Результаты поиска

Содержание N5990A-155

Отзывы:

Похожие инструкции для N5990A-155

Бренды по названию

Популярные бренды