Keysight N5990A-155 Скачать руководство пользователя страница 16

Страница: 16 / 106

Keysight N5990A-155 DisplayPort User Guide

ValiFrame DisplayPort Station

• Simple 5V supply: The simple 5V power supply is just to power on a

DUT, but not to test any PDOs. You may use any fixed 5V supply with a

current capability that is sufficient for the DUT. The recommended

minimum current is 500mA.

For more information about the PDOs support and configuration, refer to

Keysight N5990A Type-C Extension User Guide

Test Instrument Configuration

Once the DisplayPort station is configured, the instrument addresses must

be set. An example of the instrument configuration is shown in

Figure 4

DisplayPort Instruments Configuration Window

After the installation process, all instruments are configured by default in

Offline

mode. In the simulation mode, hardware need not necessarily be

physically connected to the test controller PC. The ValiFrame cannot

connect to any instrument in this mode. In order to control the instruments

that are connected to the PC, the instrument address must be entered.

The address depends on the bus type used for the connection, for

example, GPIB (General Purpose Interface BUS) or LAN (Local Area

Network). Most of the instruments used in the DisplayPort station use a

Содержание N5990A-155











































































































Результаты поиска

Содержание N5990A-155

Отзывы:

Похожие инструкции для N5990A-155

Бренды по названию

Популярные бренды

Keysight N5990A-155, Руководство пользователя

Результаты поиска

Содержание N5990A-155

Отзывы:

Похожие инструкции для N5990A-155

Бренды по названию

Популярные бренды