Keysight N5990A-155 Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 106

background image

80

Keysight N5990A-155 DisplayPort User Guide

5

Sink Calibration Procedures

For Sink Test Procedures, the basic approach is always the same:
• Achieve frequency lock
• Achieve symbol lock
• Configure the DUT for error counting
• Verify the error counting
• Run the BER test

Before starting the Sink tests, it is recommended that you click “Query

DUT Capabilities” in the “Advanced Product Configuration”. Then, the AUX

Controller communicates with the DUT, and the DUT capabilities are

displayed. This ensures that the AUX Controller is able to communicate

with the DP-controller inside the DUT before you start running the tests.

The Sink tests for DisplayPort are implemented according to the section

“Sink Compliance Test” of the DisplayPort 1.4/Type-C CTS.

The Sink test groups are divided according to Lanes (0–3) and further

divided by supported data rates (RBR, HBR, HBR2 and HBR3). There are

three types of tests:
• Jitter Tolerance Tests (at TP3)
• TP2 Tests
• Expert Mode Tests

presents a description of the procedure parameters used in

different Sink Rx tests.

Table 7

DisplayPort Receiver Parameters

NOTE

The real-time oscilloscope is not needed for Rx tests.

Parameter name

Parameter Description

Bit Error Rate Testing

Link Quality Pattern Hint

Represents the link quality pattern that is written to the DPCD register according to the specification. Make sure that
this value is in sync with the Sequence File property.

Observation Time

The time interval (in seconds) when the PRBS pattern is sent out.

Allowed Number of Errors

Maximum allowed number of errors in order to pass the test.

«
...
78
79
80
81
82
...
»

Содержание N5990A-155











































































































Отзывы:

Нет отзывов

Похожие инструкции для N5990A-155

Бренд: Kapriol Страницы: 32

Бренд: JABO Страницы: 4

Бренд: GE Страницы: 2

Druck DPI 620 Genii

Бренд: GE Страницы: 154

Arize Element Top Light

Бренд: GE Страницы: 2

Бренд: Datex-Ohmeda Страницы: 104

Druck DPI 620 Genii

Бренд: Baker Hughes Страницы: 166

Druck DPI 620 Genii

Бренд: Baker Hughes Страницы: 340

Бренд: Ace Страницы: 17

Бренд: ACE INSTRUMENTS Страницы: 33

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: TapFlo Страницы: 35

Бренд: DANA Страницы: 8

Бренд: 2E Страницы: 6

Бренд: Ibiza Страницы: 21

Бренд: IBC Страницы: 8

Бренд: Ibanez Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды