Keysight N5990A-155 Скачать руководство пользователя страница 30

Страница: 30 / 106

Keysight N5990A-155 DisplayPort User Guide

Calibration and Test Procedures

Results

Run-Time Data Display

Most procedures generate data output. While the procedure is running,

the data is displayed in a temporary MS Excel worksheet or HTML page

(depending on the selected results viewer in the Station Selection), which

appear automatically for each individual procedure.

The MS-Excel worksheet or the HTML page that are displayed temporarily

during the procedure runs are thereby closed, once the specific procedure

is finished. As long as the N5990A Software is running, each worksheet or

page can be reopened with a double-click on the respective procedure.

However, the individual worksheets or pages are lost when the N5990A

main window is closed, unless you saved them.

Results Workbook

All calibration and test data worksheets can be saved any time in a

workbook by selecting “

File > Save Results as Workbook...

”. It is

recommended that this step be carried out at least at the end of each

N5990A run. If the calibration and test procedures are conducted several

times during the same instance of N5990A, the result worksheets are

combined in the workbook. If a test procedure is conducted without

performing calibration procedures prior to the same test run, only the test

results will be saved to the workbook.

NOTE

As a safety feature, all calibration and test results are saved by default to

the ValiFrame “Tmp” directory (refer to the

N5990A Getting Started

Guide

). The sub-folder “

Results/DisplayPort Station

” contains the Excel

files of the final results measured at each calibration and of the test

procedures. In addition to the calibration data worksheets, the

calibration data files are generated. These files are saved by default to

the N5990A calibrations folder. If these calibrations are run again, the

data files are overwritten. In order to save the calibration data files for

each configuration, the files must be copied from the directory:

C:\

ProgramData\BitifEye\ValiFrameK0\DisplayPort\Calibrations

and saved

manually in another folder before rerunning the calibrations.

Содержание N5990A-155











































































































Результаты поиска

Содержание N5990A-155

Отзывы:

Похожие инструкции для N5990A-155

Бренды по названию

Популярные бренды

Keysight N5990A-155, Руководство пользователя

Результаты поиска

Содержание N5990A-155

Отзывы:

Похожие инструкции для N5990A-155

Бренды по названию

Популярные бренды