Keysight Technologies N5221BU-605 Скачать руководство пользователя страница 46

Страница: 46 / 88

46 Installation Note N5222-90114

Installation Procedure for the Upgrade

Step 29. Install the A13 13.5 GHz (Source 2) Synthesizer Board and

Cables

Refer to

Figure 25 on page 47

for this part of this step of the procedure. New

parts are listed in

Table 2 on page 11

Install new gray cable W67 (N5242-60030) to connector J5 of the new

A13 (source 2) synthesizer board (N5240-60074). The loose end of the

cable will be connected on the A10 frequency reference board (J7) after

the A13 source 2 synthesizer board has been installed in the analyzer.

2. Install the A13 board into slot 2 in the motherboard. Secure the board into

the chassis using two screws (item



; 0515-0380). To see an image

showing the location of the A13 board in the motherboard, click the

Chapter 6 bookmark “Top Assemblies, All Options” in the PDF Service
Guide

3. Connect cable W2 (N5222-20090) between the A8 source 2 board and the

A13 (source 2) synthesizer board. Tighten the cable connectors to 10

in-lbs using a 5/16-in torque wrench.

4. Connect the loose end of new gray flex cable W67 (N5242-60030) on the

A10 frequency reference board (J7). (The other end of this cable was

previously connected to J5 of the A13 (source 2) synthesizer board.)

1. See

“Downloading the Online PNA Service Guide” on page 8

Содержание N5221BU-605

























































































Результаты поиска

Содержание N5221BU-605

Отзывы:

Похожие инструкции для N5221BU-605

Бренды по названию

Популярные бренды

Keysight Technologies N5221BU-605, Установочная инструкция

Результаты поиска

Содержание N5221BU-605

Отзывы:

Похожие инструкции для N5221BU-605

Бренды по названию

Популярные бренды