Keysight Technologies N5221BU-605 Скачать руководство пользователя страница 75

Страница: 75 / 88

Installation Note N5222-90114 75

Installation Procedure for the Upgrade

Step 51. Enable Option 405

Procedure Requirements

— The analyzer must be powered up and operating to perform this procedure.
— The Network Analyzer program must

not

be running.

— Refer to the license message you received from Keysight: Verify that the

analyzer’s model and serial numbers match those on the license message

you received from Keysight.

— A keyboard must be connected to the network analyzer.

Option Enable Procedure

Locate the email(s) from Keysight which contain license file attachments.

These emails are a result of

“License Key Redemption” on page 6

Copy the license file(s) from the email(s) to the

root directory

of the USB

flash drive.

More than one license file may be copied to the USB flash drive.

Insert the USB flash drive into the PNA’s USB drive slot.

Connect the USB flash drive to the PNA. Within 5 seconds, the PNA

should display a small “New licenses installed” message.

Else, load the license key file(s), manually move your license file(s) to

C:\Program Files\Agilent\licensing

. It may take Keysight License

Manager an extra ~5 seconds to enable the licenses.

Disconnect the USB flash drive from the PNA.

On the analyzer, click or press to open the KLM software from your PNA’s

Windows taskbar by pressing

Start

More Programs

Keysight License

Manager folder

Keysight License

Manager and verify the options are

correct.

For this step, you will need a USB flash drive.
A single license file may contain more than one feature.

A single license file may contain more than one feature.

Attempting to re-install a license file that is already installed may generate

a “Corrupt Media” error message. Ignore this message.

Содержание N5221BU-605

























































































Результаты поиска

Содержание N5221BU-605

Отзывы:

Похожие инструкции для N5221BU-605

Бренды по названию

Популярные бренды

Keysight Technologies N5221BU-605, Установочная инструкция

Результаты поиска

Содержание N5221BU-605

Отзывы:

Похожие инструкции для N5221BU-605

Бренды по названию

Популярные бренды