Keysight Technologies N5221BU-605 Скачать руководство пользователя страница 5

Страница: 5 / 88

Installation Note N5222-90114

Getting Prepared

To successfully install this upgrade kit, you will need the following:
— A license key - refer to

“License Key Redemption”

below.

— A PDF copy or a paper copy of the PNA Service Guide - refer to

“Downloading the Online PNA Service Guide”

below.

— An ESD-safe work area - refer to

“Protecting Your Workspace from

Electrostatic Discharge”

below.

— Correct tools - refer to

“Tools Required for the Installation” on page 9

The PNA contains extremely sensitive components that can be ruined if

mishandled. Follow instructions carefully when making cable connections,

especially wire harness connections.
The person performing the work accepts responsibility for the full cost of

the repair or replacement of damaged components.

IMPORTANT!

Before you begin this upgrade:

—

Verify your instrument’s firmware is: A.13.55 or greater.

—

Verify your instrument’s IF Multiplexer (

IF MUX

) board, has P4, P204,

P404, P604, P804 connectors. If not, Keysight will purchase a new IF

MUX board. Refer to your instrument’s Service Guide, Chapter 7

bookmark “Removing and Replacing the A20 IF Multiplexer Board” in
the PDF Service Guide

—

Verify your Synthesizer board is version H or greater. If not, refer to

Appendix A:, “Synthesizer Board Upgrade (N5240-60074 (with

Tabs)/N5240-60076 (Without Tabs) Version F/G to Version H),” on

page A-1

a. See

“Downloading the Online PNA Service Guide” on page 8

IMPORTANT!

—

This document contains references to legacy and new A21 HMA26.5
Multiplier/Amplifier assemblies. Your model instrument may have

either legacy assemblies or the new parts installed. Both types of

assemblies are compatible with this upgrade. This note is for your

reference, because some figures contain legacy assemblies that

your instrument may not have installed.

—

To verify your instrument’s A21 HMA26.5 Multiplier/Amplifier, refer

“Verify the Model/Version of HMA26.5 Installed” on page 7

—

See also your instrument’s PDF Service Guide

a. See

“Downloading the Online PNA Service Guide” on page 8

Содержание N5221BU-605

























































































Результаты поиска

Содержание N5221BU-605

Отзывы:

Похожие инструкции для N5221BU-605

Бренды по названию

Популярные бренды

Keysight Technologies N5221BU-605, Установочная инструкция

Результаты поиска

Содержание N5221BU-605

Отзывы:

Похожие инструкции для N5221BU-605

Бренды по названию

Популярные бренды