Keysight Technologies N5221BU-605 Скачать руководство пользователя страница 14

Страница: 14 / 88

Installation Note N5222-90114

Items Included in the Upgrade Kit

Ribbon cable, A19 test set motherboard J213 to A24 mixer brick (2)

N5242-60006

–

Cable, DC – 2 pin to R/A SMP (Port 3 bias combiner DC to A19 Bias J543 and Port 4

bias combiner DC to A19 Bias J544.)

N5240-60091

a. The A22 splitter (

5087-7139) and

N5222-20007, N5222-20008, and N5222-20009 cables are only used with a legacy

HMA26.5 p/n: 5087-7765. If your PNA has a new N5240-60101 assembly installed, then set aside these parts as spares for

use in other PNAs with the older HMA26.5 or discard. If you are unclear which HMA26.5 assembly your PNA has installed, refer

Figure 1 on page 7

b. The N5222-20126 cable is used only with instruments that have a newer HMA26.5 installed. If your PNA has a legacy

5087-7765 HMA26.5 assembly installed, then this cable can be discarded. If you are unclear which HMA26.5 assembly your

PNA has installed, refer to

Figure 1 on page 7

Extra quantities of items such as protective plastic caps, screws, cable ties, and
cable clamps may be included in this upgrade kit. It is normal for some of these
items to remain unused after the upgrade is completed.

Table 2

Contents of Upgrade Kit N5222-60124

Ref

Desig.

Description

Qty

Part Number

Содержание N5221BU-605

























































































Результаты поиска

Содержание N5221BU-605

Отзывы:

Похожие инструкции для N5221BU-605

Бренды по названию

Популярные бренды

Keysight Technologies N5221BU-605, Установочная инструкция

Результаты поиска

Содержание N5221BU-605

Отзывы:

Похожие инструкции для N5221BU-605

Бренды по названию

Популярные бренды