Keysight Technologies N5221BU-605 Скачать руководство пользователя страница 12

Страница: 12 / 88

12 Installation Note N5222-90114

Items Included in the Upgrade Kit

–

Machine screw, M3.0 x 6, flat head (to attach dress panel to coupler plate)

0515-1946

–

Machine screw, M2.5 x 14, pan head

0515-2141

Bulkhead connector for test set front plate (hardware supplied with connector)

1250-3805

Cable clamp snap-in pressure sensitive with adhesive mounting

1400-1334

–

Cable clamp pressure sensitive with adhesive mounting

1400-1391

Dust caps for test ports

1401-0214

–

Clamp – SMP – instrument

5023-3299

–

Microwave splitter

5087-7139

–

Cable assy coax – 205 mm long

8120-5017

–

Gap pad (between each test coupler and the test set front plate)

E4403-20033

Test set front plate (subpanel), 4-port

N5221-00007

–

Front panel, dress panel, lower, 4-port

N5222-00009

–

Cable guard, center jumper cables

N5242-00049

Front panel overlay (label), 4-port (Options 405, 420, and 425)

N5222-80036

Short, installed on A24 mixer brick

0960-0055

Mounting nuts (for port 3 & 4 test port couplers)

5022-1087

RF cable, 13.5 GHz (source 2) synthesizer board J1207

to A8 26.5 GHz source (2) board P1 – Top Cable – All Options – 4-Port

N5222-20090

RF cable, A8 source (2) board P5 to W6 on bottom of analyzer – Top Cable

N5222-20062

RF cable, W5 to A26 port 3 receiver coupler

N5222-20041

RF cable, A8 source (2) board P3 to W8 on bottom of analyzer – Top Cable

N5222-20063

RF cable, W7 to A23 port 4 receiver coupler

N5222-20042

W14

RF cable, A29 port 1 coupler to front-panel Port 1 CPLR ARM

N5222-20030

W15

RF cable, A26 port 3 receiver coupler to front-panel Port 3 SOURCE OUT

N5222-20047

W17

RF cable, A26 port 3 receiver coupler to front-panel REF 3 SOURCE OUT

N5222-20023

W18

RF cable, A30 port 3 coupler to front-panel Port 3 CPLR ARM

N5222-20015

W19

RF cable, A23 port 4 receiver coupler to front-panel Port 4 SOURCE OUT

N5222-20050

W21

RF cable, A23 port 4 receiver coupler to front-panel REF 4 SOURCE OUT

N5222-20025

W22

RF cable, A31 port 4 coupler to front-panel Port 4 CPLR ARM

N5222-20018

Table 2

Contents of Upgrade Kit N5222-60124

Ref

Desig.

Description

Qty

Part Number

Содержание N5221BU-605

























































































Результаты поиска

Содержание N5221BU-605

Отзывы:

Похожие инструкции для N5221BU-605

Бренды по названию

Популярные бренды

Keysight Technologies N5221BU-605, Установочная инструкция

Результаты поиска

Содержание N5221BU-605

Отзывы:

Похожие инструкции для N5221BU-605

Бренды по названию

Популярные бренды