Keysight Technologies N5221BU-605 Скачать руководство пользователя страница 64

Страница: 64 / 88

64 Installation Note N5222-90114

Installation Procedure for the Upgrade

Connect New Port 4 N5240-60098 (x1) and Verify Port 2 N5240-60097

Blue Bias-Tee Combiner Cables and Clamps from the A73 and A74 Bias

Tees “RF-IN” to the A70 LFE Board “Port2” and “Port4” Connectors and

Install Clamps onto the Ferrite Beads

Install the N5240-60097 (x1) and N5240-60098 (x1) cable as shown. Note
the orientation of the cable (item



through



Figure 37

Connect new N5240-60098 from Port 4 and verify N5240-60097 from Port 2

Bias Tee Combiners to A70 LFE Board and Install Clamps onto the Ferrite

Beads (N5240-60098 (x1), and 1400-1391 (x3))

Verify Port

2 cable is

properly

routed and

secured.

Содержание N5221BU-605

























































































Результаты поиска

Содержание N5221BU-605

Отзывы:

Похожие инструкции для N5221BU-605

Бренды по названию

Популярные бренды

Keysight Technologies N5221BU-605, Установочная инструкция

Результаты поиска

Содержание N5221BU-605

Отзывы:

Похожие инструкции для N5221BU-605

Бренды по названию

Популярные бренды