Keysight Technologies N5221BU-605 Скачать руководство пользователя страница 29

Страница: 29 / 88

Installation Note N5222-90114 29

Installation Procedure for the Upgrade

Refer to

Figure 9

for this step of the procedure. New parts are listed in

Table 2

on page 11

. Use a T-10 TORX driver to remove all screws.

Remove 5023-3299 (x2) clamps and 0515-2141 (x2) clamp screws as
shown (item



Remove the W177 – N5240-60097 (x1) cable as shown. Note the
orientation of the cable (item



). Save this cable for reuse.

Remove the W174 – N5240-60098 (x1) cable as shown. Note the
orientation of the cable (item



). Save this cable for reuse.

Figure 8

Remove the cables and clamps to the bias tee combiners (N5240-60098,

N5240-60097, 5023-3299, and 0515-2141)

These cables are reused, but the cable routing is different for a 4-port

instrument.

Содержание N5221BU-605

























































































Результаты поиска

Содержание N5221BU-605

Отзывы:

Похожие инструкции для N5221BU-605

Бренды по названию

Популярные бренды

Keysight Technologies N5221BU-605, Установочная инструкция

Результаты поиска

Содержание N5221BU-605

Отзывы:

Похожие инструкции для N5221BU-605

Бренды по названию

Популярные бренды