Keysight Technologies N5221BU-605 Скачать руководство пользователя страница 17

Страница: 17 / 88

Installation Note N5222-90114

Installation Procedure for the Upgrade

“Step 46. DC Continuity Test the LFE Board and Test Ports.”

“Step 47. Position the Cables and Wires to Prevent Pinching.”

“Step 48. Reinstall the Inner Cover.”

“Step 49. Reinstall the Outer Cover.”

“Step 50. Remove Option 205 License.”

“Step 51. Enable Option 405.”

“Step 52. Verify the PNA Analyzer Program is Running with the Correct

Options.”

“Step 53. Perform Post-Upgrade Adjustments and Calibration.”

“Step 54. Prepare the PNA for the User.”

Step 1. Obtain a Keyword and Verify the Information

Follow the instructions on the Software Entitlement Certificate supplied to

obtain a license key file for installation of this upgrade. Refer to

“License Key

Redemption” on page 6

Verify that the model number, serial number, and option number information

on the license key match those of the instrument on which this upgrade will be

installed.
Once the license key file has been received and the information verified, you

can proceed with the installation at step 2.

Step 2. Remove the Outer Cover

For instructions, click the Chapter 7 bookmark “Removing the Covers” in the

PDF Service Guide.

Step 3. Remove the Inner Cover

For instructions, click the Chapter 7 bookmark “Removing the Covers” in the

PDF Service Guide1.

If the model number, serial number, or option number do not match those

on your license key file, you will not be able to install the option. If this is

the case, contact Keysight for assistance before beginning the installation

of this upgrade. Refer to

“Contacting Keysight” on page 4

Содержание N5221BU-605

























































































Результаты поиска

Содержание N5221BU-605

Отзывы:

Похожие инструкции для N5221BU-605

Бренды по названию

Популярные бренды

Keysight Technologies N5221BU-605, Установочная инструкция

Результаты поиска

Содержание N5221BU-605

Отзывы:

Похожие инструкции для N5221BU-605

Бренды по названию

Популярные бренды