Keysight Technologies N5221BU-605 Скачать руководство пользователя страница 20

Страница: 20 / 88

20 Installation Note N5222-90114

Installation Procedure for the Upgrade

Step 7. Disconnect A71 and A74 Bias-Tee Combiner’s LFE Cables

From the A70 Low Frequency Extension (LFE) Board and the Ends of

the LFE Cables Connected to the IF Multiplier (IF MUX) Board

Disconnect the (8120-5014 (x2), 8120-5017 (x1), and 8120-5021 (x1)) IF
gray cables item



through item



as shown in

Figure 1

. (i.e., one end is

removed in

“Step 9. Remove Some Low Frequency Extension (LFE) Cables

(8120-5014 (x1), 8120-5021 (x1), N5240-60097 (x1), and N5240-60098

(x1)) From the IF Multiplexer (IF MUX) Board” on page 22

Save: 8120-5014 (x2) and 8120 (x1) for reuse.

Discard: 8120-5021.

Disconnect the N5242-60078 Source 1 and N5242-60080 LO Source
cables from the LFE board as shown – (items



and



). The other end of

the N5242-60078, N5242-60079 does

not

need to be disconnected from

the Source1 and LO Source boards. Refer to

Figure 1

and

Figure 41 on

page 70

Figure 1

Disconnect A71 and A74 bias-T combiners new cables to the A70 LFE board

the other ends of the LFE cables to the LFE Board (8120-5014 (x2),

8120-5017 (x1), 8120-5021 (x1), N5242-60078, and N5242-60080)

Содержание N5221BU-605

























































































Результаты поиска

Содержание N5221BU-605

Отзывы:

Похожие инструкции для N5221BU-605

Бренды по названию

Популярные бренды

Keysight Technologies N5221BU-605, Установочная инструкция

Результаты поиска

Содержание N5221BU-605

Отзывы:

Похожие инструкции для N5221BU-605

Бренды по названию

Популярные бренды