manualshive.com logo in svg

Kenwood NX-5000 series, Руководство пользователя

Поделиться
Скачать
Kenwood NX-5000 series Скачать руководство пользователя страница 184

4.3

Transceiver Behavior upon Transmission of Encrypted
Communication Data

The behavior of the transceiver when the transceiver encrypts and sends communication data differs depending on the
configuration in 

Encryption

 for the P25 digital channel or the configuration in 

Encryption

 for the Talkgroup ID List as follows:

0

Clear

The transceiver always sends communication data without encrypting the data. Even if 

Encryption

 is enabled by

operating the transceiver, the transceiver sends communication data without encrypting the data.

0

Secure

The transceiver always encrypts and sends communication data. Even if 

Encryption

 is disabled by operating the

transceiver, the transceiver encrypts and sends communication data.

0

Select

The transceiver encrypts and sends communication data if 

Encryption

 is enabled. The transceiver sends communication

data without encrypting the data if 

Encryption

 is disabled.

Either “Secure” or “Select” needs to be configured in 

Encryption

 mentioned above in order to encrypt and send

communication data.

Note

0

The status of Encryption can be toggled between enabled or disabled by using the 

Scrambler/Encryption

 key or 

Menu

key. (Refer to 

Toggling the Encryption during Transmission between Enabled and Disabled

.)

0

If the Encryption Key (Key ID and Key Data) used to encrypt communication data is deleted, “Key Fail” appears on the
transceiver display and a Key Fail Alert Tone (6 beeps) sounds from the transceiver when the 

PTT

 switch is pressed to

transmit data. In this case, the transceiver cannot transmit.

Data Encryption

Whether to encrypt and send a Text Message, GPS data, or OTAP control data can be switched by toggling the status of
Scrambler/Encryption between enabled and disabled using the 

Scrambler/Encryption

 key or Menu Mode.

In a P25 Conventional system, the configuration for encrypting a Text Message, GPS data, or OTAP control data can be
done for each system.
If 

KMF Profile

 is disabled, data is encrypted according to each configuration in 

Multi-key List Number

, regardless of the

OTAR configuration for the current channel. If 

KMF Profile

 is enabled, data is encrypted according to each configuration

in 

EKR List Number

, regardless of the OTAR configuration for the current channel.

An icon indicating the encryption type for the transmitting channel appears during Text Messaging Mode or the length of
time from when the transceiver starts sending a Text Message or GPS data until the transceiver finishes the transmission.
An icon indicating the encryption type for the transmitting channel also appears during the length of time from when the
transceiver starts sending OTAP control data after entering OTAP Mode until the transceiver exits OTAP Mode.

Configuration using KPG-D1/ D1N

0

Configuring 

Multi-key List Number

 for data communications (

 Transceiver Settings > Personal > Personal

Features > P25 Conventional (P25 Voting with NAC) > Encryption > Multi-key List Number)

0

Configuring 

EKR List Number

 for data communications (

 Transceiver Settings > Personal > Personal Features

> P25 Conventional (P25 Voting with NAC) > Encryption > EKR List Number)

4 COMMUNICATION SECURITY

4.3 Transceiver Behavior upon Transmission of Encrypted Communication Data

P25 FUNC (K)/Ver 2.20

164

CONTENTS

INDEX

Содержание NX-5000 series









































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды