KaVo ORTHOPANTOMOGAPH OP 2D Скачать руководство пользователя страница 18

Страница: 18 / 128

ORTHOPANTOMOGAPH OP 2D

General Information

Patient Positioning Lasers

Check that the patient positioning lasers work and are

positioned correctly. Refer to the Installation and set-up

manual for information on how to do this.

Mains power supply cable

Check the condition of main power supply cable and

replace it if damaged.

Mains power switch

Check the operation of the mains power switch. Re-

place the switch if it appears faulty or otherwise not

working properly.

Tubehead

Make sure that oil is not leaking from the tubehead. If

the tubehead shows signs of oil leakage, replace it.

Fire risk

WARNING:

Disconnect the unit from the main power

supply before carrying out the next task.

To eliminate the risk of

re use a vacuum cleaner to re-

move all dust that has accumulated inside the unit and

cover air vents. Remove all dust from the circuit boards,

and pay special attention to the Generator board L1800,

PFC P1910 and EMC shield holes.

Covers and Labels

Check that all covers are correctly installed and in good

condition. Also check that all the labels are attached to

the unit and that they are all legible.

Содержание ORTHOPANTOMOGAPH OP 2D

































































































































Результаты поиска

Содержание ORTHOPANTOMOGAPH OP 2D

Отзывы:

Похожие инструкции для ORTHOPANTOMOGAPH OP 2D

Бренды по названию

Популярные бренды

KaVo ORTHOPANTOMOGAPH OP 2D, Руководство по обслуживанию

Результаты поиска

Содержание ORTHOPANTOMOGAPH OP 2D

Отзывы:

Похожие инструкции для ORTHOPANTOMOGAPH OP 2D

Бренды по названию

Популярные бренды