KaVo ORTHOPANTOMOGAPH OP 2D Скачать руководство пользователя страница 106

Страница: 106 / 128

ORTHOPANTOMOGAPH

7. Replacing parts

5. Remove the collimator assembly by removing

the two (2) pointed screws.

NOTICE!

It's good to use a pen to mark the corner lo-

cations of the collimator assembly, as shown

in the image. With the markings it's easier to

re-assemble the collimator assembly after the

replacement of tubehead.

6. Remove the four (4) nuts that hold the

tube-

head

to the

rotating unit frame

and remove

the tubehead.

7. Attach the

new tubehead

to the rotating unit

frame with the four (4) nuts.

NOTICE!

When tightening the tubehead fastening nuts,

prevent the screws from rotating.

8. Reattach the collimator assembly using the

markings as the indicator for the approximate

location.

NOTICE!

The markings do not guarantee that the unit

alignment remains the same, but they ease the

alignment adjustment work required after the

tubehead replacement.

9. Reconnect all the cables.

Содержание ORTHOPANTOMOGAPH OP 2D

































































































































Результаты поиска

Содержание ORTHOPANTOMOGAPH OP 2D

Отзывы:

Похожие инструкции для ORTHOPANTOMOGAPH OP 2D

Бренды по названию

Популярные бренды

KaVo ORTHOPANTOMOGAPH OP 2D, Руководство по обслуживанию

Результаты поиска

Содержание ORTHOPANTOMOGAPH OP 2D

Отзывы:

Похожие инструкции для ORTHOPANTOMOGAPH OP 2D

Бренды по названию

Популярные бренды