KaVo ORTHOPANTOMOGAPH OP 2D Скачать руководство пользователя страница 19

Страница: 19 / 128

1. General Information

ORTHOPANTOMOGAPH OP 2D

1.7 Disposal

At the end of useful working life of the unit, its spare

and replacement parts and accessories make sure that

you follow all local, national and international regula-

tions regarding the correct and safe disposal and/or

recycling of the unit, its spare and replacement parts

and accessories.

The unit and its spare parts and accessories may in-

clude parts that are made of or include materials that

are non-environmentally friendly or hazardous. These

parts must be disposed of in accordance with all lo-

cal, national and international regulations regarding the

disposal of non-environmentally friendly or hazardous

materials.

The following hazardous materials and substances can

be found in the unit, its spare and replacement parts

and assemblies:

- Lead (Pb):

circuit boards, tubehead, collimator,

CCD sensor assembly

- Cadmium (Cd):

none

- Mercury (Mg):

none

- PBB Polybrominated biphenyls:

none

- PBDE polybrominated diphenyl ethers:

none

Other materials and substances in the unit, its spare

parts and assemblies that could be hazardous and are

non-environmentally friendly are:

- Mineral oil:

tubehead

Содержание ORTHOPANTOMOGAPH OP 2D

































































































































Результаты поиска

Содержание ORTHOPANTOMOGAPH OP 2D

Отзывы:

Похожие инструкции для ORTHOPANTOMOGAPH OP 2D

Бренды по названию

Популярные бренды

KaVo ORTHOPANTOMOGAPH OP 2D, Руководство по обслуживанию

Результаты поиска

Содержание ORTHOPANTOMOGAPH OP 2D

Отзывы:

Похожие инструкции для ORTHOPANTOMOGAPH OP 2D

Бренды по названию

Популярные бренды