KaVo ORTHOPANTOMOGAPH OP 2D Скачать руководство пользователя страница 87

Страница: 87 / 128

4. Troubleshooting

ORTHOPANTOMOGAPH OP 2D

Error E12 (CCD line failure)

CAUSE

The image data

ow from the CCD sensor to L1200

was interrupted during the exposure.

SOLUTION

Refer to the trouble shooting information given in error

code E11.

Error E13 (CCD error, CCD EEPROM CRC test failed)

CAUSE

L1200 CPU failed to read CCD con

guration param-

eters.

SOLUTION

Reboot the unit. If the problem persists, change the

CCD sensor.

Error E14 (Tubehead disconnected)

CAUSE

SW has detected that the tubehead is not connected or

is not able to read the thermal sensor status.

SOLUTION

Check the tube head connections.

Error E16 (Z lift not allowed due to duty cycle)

CAUSE

Z-motor over heated.

SOLUTION

Allow motor to cool down.

Содержание ORTHOPANTOMOGAPH OP 2D

































































































































Результаты поиска

Содержание ORTHOPANTOMOGAPH OP 2D

Отзывы:

Похожие инструкции для ORTHOPANTOMOGAPH OP 2D

Бренды по названию

Популярные бренды

KaVo ORTHOPANTOMOGAPH OP 2D, Руководство по обслуживанию

Результаты поиска

Содержание ORTHOPANTOMOGAPH OP 2D

Отзывы:

Похожие инструкции для ORTHOPANTOMOGAPH OP 2D

Бренды по названию

Популярные бренды