en
HD 2/150 Operating Instructions
16
Please dispose of the packaging in an
environmentally friendly way
The packaging is recyclable. Please do not
throw the packaging in the domestic waste but
in a recycling collection point.
Please dispose of old, used cleaners in
an environmentally friendly way
Used cleaners contain valuable recyclable
materials, which should be disposed of in a
suitable collection point for reuse. Batteries, oil
and similar materials must not be allowed to get into the
environment. Therefore, please dispose of old units in
suitable waste collection systems.
Please do not allow motor oil, heating
oil, diesel and benzine
to get into the environment. Please protect the soil and
dispose of waste oil in an environmentally friendly way.
Please do not allow waste water
containing mineral oil
to get into the ground, bodies of water or the sewers.
Unpack the unit
When unpacking the unit, check the contents of the
packaging. If transportation damage has occurred,
inform your dealer.
Place the unit on firm ground and actuate the parking
brake.
Check the oil level
Screw out the fastening screws on the left and right
of the unit cover, remove unit cover.
Cut off the tip on the cover to the oil reservoir.
Check the oil level in the oil reservoir. The oil must
reach the middle mark on the oil tank when the unit is
level.
Fasten the unit cover again.
A start-up is performed
– after unpacking the unit
– if the unit has been shut down.
Connect the high-pressure hose.
Remove protective caps from the ends of the hose
and keep in the tool bag.
The hose end with the long control cable is
connected to the pump head.
To protect the hose end from kinking, guide it down
between the handle and the unit.
The conical nipple of the high-pressure hose must
project over the screw-in end by 4–5 mm.
To adjust the spacing, turn the sleeve by hand or with a
pair of pliers (Caution! left-hand thread).
Lubricate the internal thread on the high-pressure
hose with the enclosed stainless-steel grease.
Manually screw the high-pressure hose into the high-
pressure connection on the pump head and tighten
with a size 17 open-end wrench.
Connect the control cable to the controller.
Connect the control cable on the other end of the
hose to the handgun.
Do not yet connect the high-pressure vent hose to the
handgun.
Environmental protection
Preparing the unit for use
Switching on the unit
Содержание HD 2/150
