K-TRON KSU-II/KCM Скачать руководство пользователя

Страница: 77 / 121

Docu-No.: 0590020601-EN Rev. 1.6.0

Page 77

Alarm Messages- Cause and Remedy

Display messages 4.3

4.3

Display messages

4.4

Feeder won’t start - displayed messages

4.5

Feeder won’t run in GRAV

Message

Cause

Remedy

Out of Range
Tare Failed

• Maximum permissible input value

has been exceeded.



Enter a value within the permitted
limits of the parameter. See the
specific programming manual for
more information.

Nak’d Feeder
Running

• Not acknowledged as the command

cannot occur when the feeder is
running.



Stop the feeder before making the
entry.

Message

Cause

Remedy

Wait

• No setpoint is entered.

• Feedfactor, if required, is <0>.

• Interlock has failed.



Enter an operating <SP>.



Enter an <Initial Feedfactor>.



Check interlocks.

Alsh

• Automatic alarm shutdown because

of an alarm.



Correct alarm problem and then
clear the alarm with the

ALARM

key.

Disa

• Start via bit input disabled. (Interlock

or Run enable).



Check interlocks to the KCM.

Message

Cause

Remedy

Feeder remains in
VOL control

• Conditions for gravimetric control

not fulfilled.



Check input for forced VOL
function.



If LWF, check refill function and net
weight.



Check for weight related alarms.



Check for weight less than <Net
Weight Low> Limit.



Check for weight greater than <Net
Weight High> limit.

Содержание KSU-II/KCM


























































































































Результаты поиска

Содержание KSU-II/KCM

Отзывы:

Похожие инструкции для KSU-II/KCM

Бренды по названию

Популярные бренды

K-TRON KSU-II/KCM, Инструкция по программированию

Результаты поиска

Содержание KSU-II/KCM

Отзывы:

Похожие инструкции для KSU-II/KCM

Бренды по названию

Популярные бренды