K-TRON KSU-II/KCM страница 58 Скачать руководство пользователя

Страница: 58 / 121

Programming Reference

1.11System setup (only KSU-II/KCM).

Page 58

Docu-No.: 0590020601-EN Rev. 1.6.0

1.11

System setup (only KSU-II/KCM).

This menu programs the key communication functions for the KCM.

Note:

• Siemens 3694R protocol is not supported.

1.11.1

Communication sub-menu

This menu is only used with the KSU-II/KCM display and not available
for KSL, K-Vision or KSC.

Parameter

Definition

HOST PROT

Input of the desired communication protocol

Input range: Modbus, ALLEN BRAD AB-CIF, Siemens 3694R,
ProfibusDP, Modbus/TCP, DeviceNet, Ethernet/IP, ModbusPlus,
Profinet IO.

Default: None

HOST FILE

Select either a custom downloaded *.kgr file for data
communications or select a pre-loaded file (built-in). See manual
0590020611 for details.

Input range: Kgr File, Small, Full.

Default: Kgr File

IP Adress

Only present when an Ethernet Host board is installed.

If the KGR file is used, this parameter is read-only.

Net Mask

Only present when an Ethernet Host board is installed.

If the KGR file is used, this parameter is read-only.

GateOnly present when an Ethernet Host board is installed.

If the KGR file is used, this parameter is read-only.

K-PORT1 PROT

Selects the function for K-Port1, Choices are: None, KSU, KSL,
KSC/K-Vision.

Default: KSU

BAUD RATE

Displays baud rate selections when K-Port1 is set to KSC/K-Vision
or if set to KSL and the service variable K10S_KCDR is <1>.

Choices are: 9600, 19200, 38400, 57600, 115200

K-PORT 2 PROT

Selects the function for K-Port2, Choices are: None, KSU, Modbus I-
O, KSC/K-Vision.

Default: KSU

Table page 1 of 2

Содержание KSU-II/KCM


























































































































Результаты поиска

Содержание KSU-II/KCM

Отзывы:

Похожие инструкции для KSU-II/KCM

Бренды по названию

Популярные бренды

K-TRON KSU-II/KCM, Инструкция по программированию

Результаты поиска

Содержание KSU-II/KCM

Отзывы:

Похожие инструкции для KSU-II/KCM

Бренды по названию

Популярные бренды