K-TRON KSU-II/KCM Скачать руководство пользователя

Страница: 76 / 121

Alarm Messages- Cause and Remedy

4.2 LWF alarms

Page 76

Docu-No.: 0590020601-EN Rev. 1.6.0

4.2

LWF alarms

Process alarms

Cause

Remedy

52 FEEDFACT. BAD

• Feedfactor is zero or feeding

condition changed so that the
feedfactor exceed the set limit in the
<ALARM> menu <FF DEV LIMIT>.



Enter new feedfactor.



Check feedfactor limit in <ALARM>
menu <FF DEV LIMIT>.



Check feeding condition.

53
SCALE
OVERRANGE

• The weight on the scale is above the

scale gross range permitted.



Check the scale for proper
operation.



If LWF, reduce level of refilling -
<REFILL MAX> parameter.

54
SCALE
UNDERRANGE

• The weight on the scale is below the

zero or gross weight < 0.



Check the scale and re-tare.

55 NETWT > LIMIT

• The material weigh in the hopper is

above the limit set in the <ALARM>
menu. <NW HI LIMIT>.



Check for proper hopper filling.



Check the tare value.



Check for scale or weigh bridge
measurement errors.

56 NETWT < LIMIT

• The material weigh in the hopper is

below the limit set in the <ALARM>
menu.<NW LO LIMIT>.



Check for proper hopper filling.



Check the tare value.



Check for scale or weigh bridge
measurement errors.

57 REFILL
EXPIRED

• The programmed refilling time

(program parameter <ALARM>
menu, <MAX REFILL TIME> was
exceeded without refilling being
completed.



Check refilling device, increase the
time in program parameter
<ALARM> menu, <ALARM
LIMTS> sub-menu, <MAX REF
TIME> or refill faster if necessary.

58 LOADER
TIMEOUT

• Loader hopper is empty



Check loader and material supply.

61
LOW CONTROL
GAIN

• Adaptive gain is 10 or below.



Check for excessive PERT values.



Reduce scale disturbances.



Increase operating setpoint.

Содержание KSU-II/KCM


























































































































Результаты поиска

Содержание KSU-II/KCM

Отзывы:

Похожие инструкции для KSU-II/KCM

Бренды по названию

Популярные бренды

K-TRON KSU-II/KCM, Инструкция по программированию

Результаты поиска

Содержание KSU-II/KCM

Отзывы:

Похожие инструкции для KSU-II/KCM

Бренды по названию

Популярные бренды