K-TRON KSU-II/KCM Скачать руководство пользователя

Страница: 73 / 121

Docu-No.: 0590020601-EN Rev. 1.6.0

Page 73

Alarm Messages- Cause and Remedy

System alarms 4.1

30
KLINK WRONG
KGR

• Protocol of KGR file does not match

that required by the installed com-
munication circuit card.



Make corrections as necessary.

31 KLINK NO KGR

• No KGR file loaded



Load KGR file with SmartConfig or
switch to <Built-IN> KGR file.

32 HPORT FAIL

• Host communication pcb error.



Check communications pcb for
proper LED operation.



Exchange communications pcb as
necessary.

33 HPORT FAIL INIT

• Host communication pcb could not

be initialized.



No host communications pcb is
installed.



Check host communications pcb
connections.



Replace host communications pcb.

34
HPORT ILLEGAL
BD

• Improper pcb installed in the host

port location.



Install correct host communications
pcb.

35 KPORT FAIL

• K-Port has failed



Replace K-Port comm pc card.

36 KPORT FAIL INIT

• K-Port communication pcb could not

be initialized.



Replace K-Port comm pc card.

37
KPORT ILLEGAL
BD

• Host communication pcb is installed

on the wrong port location-(K-Port).



Check host communications pcb
for proper mounting location.

38
KGR PARAM
ERROR

• One or more feeder parameters are

not correct for the specified feeder.



Correct KGR file.



Use <Built-IN> KGR file.

39 EXT IO FAIL

• The MODBUS I-O connection has

failed.



Check connections to remote I-O
device.



Check remote I-O device wiring.

40
EXT ALR
ACTIVATED

• Digital input on KCM selected for

External Alarm is active.



Investigate the cause of this input
being active and correct.

41 INTERLOCK
FAIL

• Drive pcb Run Enable digital input is

open during operation.



Check the Drive pcb Run Enable
digital input for proper function.

Alarm Num- Alarm

Cause

Remedy

Table page 5 of 7

Содержание KSU-II/KCM


























































































































Результаты поиска

Содержание KSU-II/KCM

Отзывы:

Похожие инструкции для KSU-II/KCM

Бренды по названию

Популярные бренды

K-TRON KSU-II/KCM, Инструкция по программированию

Результаты поиска

Содержание KSU-II/KCM

Отзывы:

Похожие инструкции для KSU-II/KCM

Бренды по названию

Популярные бренды