K-TRON KSU-II/KCM Скачать руководство пользователя страница 13

Страница: 13 / 121

Docu-No.: 0590020601-EN Rev. 1.6.0

Page 13

Programming Reference

Product change menu 1.1

AUTO FF CALIB

This action permits easy feeder calibration. For this the program
parameter <CAL DC> and <CAL TIME> have to be entered. Material
is discharged for the value of <CAL TIME> and the starting feeding
factor is calculated.

Notes:

• Calibration can be canceled with

STOP

• Pressing

ENTER

instead of

RUN

as noted above will abort the

AUTOFFCALIB routine and return the user to the HOME menu.

• Performing an AUTOFFCALIB function on an already running

feeder will have no effect upon operation.

▲

This command will start the feeder. Make sure that nobody is
working on the machine.



For KSU-II/KCM select this parameter, press

ENTER

twice

and then press

RUN



For KSL press

MORE-F5

then press

RUN



For KSC press

then

RUN

Attention:

Refilling and feeding errors during calibration reset the program pa-
rameter FF INIT to <0> and activate the <FEEDFACTOR ERR>
alarm.

CALIB REMAIN [s]

A count down timer for the auto calibrate cycle. It shows how many
seconds are left in the Calibration cycle.

INIT FF

Initial Feedfactor

Input of the starting feeding factor to determine the motor speed. The
Drive Command is calculated as follows:

DriveCommand(%) = 100 x (Setpoint/Initial Feedfactor)

The starting feed factor can also be calculated with the command
variable <AUTO FF CALIB>. Value of <0> will cause a Feedfactor
Alarm.

The feeder will not run with a Feedfactor of <0>.

Input range: 0 to 99999

Default: 100 kg/hr

Parameter

Definition

Table page 3 of 5

Содержание KSU-II/KCM


























































































































Результаты поиска

Содержание KSU-II/KCM

Отзывы:

Бренды по названию

Популярные бренды

K-TRON KSU-II/KCM, Инструкция по программированию

Результаты поиска

Содержание KSU-II/KCM

Отзывы:

Бренды по названию

Популярные бренды