K-TRON KSU-II/KCM Скачать руководство пользователя

Страница: 11 / 121

Docu-No.: 0590020601-EN Rev. 1.6.0

Page 11

Programming Reference

Product change menu 1.1

1.1

Product change menu

This menu allows easy product changeover. See section

•

for

manuals to be used specifically when calibrating the feeder.

1.1.1

Product change parameters

Parameter

Definition

REFILL

Refill Enable

ENABLED

Setting for automatic refill. The net weight alarm
limit is active.

DISABLED

The feeder hopper can be emptied without refilling
being triggered. The net weight alarm limit is
disabled.

IF RUNNING

Refill is enabled if the feeder runs, otherwise it is
disabled.

Default: DISABLED

REFILL MAX.

Refill Level Maximum

Input of the upper refilling limit at which refilling is stopped.

Warning:

Do not exceed the hopper capacity or scale capacity when entering
the top refilling limit. See section

3.1.1

Input range: <0.95 x Gross scale range

Default: 0.06 kg

REFILL MIN

Refill Level Minimum

Input of the lower refilling limit at which refilling is started. See section

3.1.2

Warning:

Feeding behavior can be affected if the refilling limit is set too low.
Do not uncover feeder horizontal agitator.

Input range: < Refill Maximum

Default: 0.05 kg

START REFILL NOW

This command starts the refill when the net weight is less the
<REFILL MAX>.

Table page 1 of 5

Содержание KSU-II/KCM


























































































































Результаты поиска

Содержание KSU-II/KCM

Отзывы:

Похожие инструкции для KSU-II/KCM

Бренды по названию

Популярные бренды

K-TRON KSU-II/KCM, Инструкция по программированию

Результаты поиска

Содержание KSU-II/KCM

Отзывы:

Похожие инструкции для KSU-II/KCM

Бренды по названию

Популярные бренды