K-TRON KSU-II/KCM Скачать руководство пользователя | Manualshive

Страница: 19 / 121

background image

Docu-No.: 0590020601-EN Rev. 1.6.0

Page 19

Programming Reference

1

Calibration 1.2

1.2.2

Feedfactors sub-menu for motor driven feeders

Parameter

Definition

REFILL ARRAY

Feedfactor Array or

Density Array

ON

Refilling feedfactor storage array is on. The feeding
factor values are stored in these registers when the
gravimetric mode is active. During refilling, the stored
feeding factor values in conjunction with setpoint are
used to establish proper drive command.

OFF

The refilling feedfactor storage array is off. The last
average feedfactor just prior to refill is used in
conjunction with setpoint to control feeding during
refilling.

Input range: On or Off

Default: Off

Notes:

• When <ON>, the Refill Array routine checks that the array FF

Empty and FF Full are within 0.5 to 2.0 times the current average
feed factor, otherwise the FF array is cleared.

• If the feed factor changes more than 15% (0.5 times the service

variable RefArr DevLim), the refill array is cleared.

FEED FACT 1, 5, 9

FF Hopper Full

FF Hopper Mid

FF Hopper Empty

Display of the feeding factor values in the refilling feedfactor array.
These factors are calculated in the gravimetric mode and used
during refilling in the volumetric mode when the refilling array
registers are activated.

Full(9) = 10% below the top refilling limit.

Middle(5) = 50% below the top refilling limit.

Empty(1)= 10% above the lower refilling limit.

Note:

Consistency of values indicate little variance in bulk material flow
properties. This is ideal. Rapidly changing bulk density can affect
feeder performance over the refill range. This would be evidenced by
widely varying values of feedfactor. If the values vary highly,
consider modifying refill levels, both maximum and minimum, to
achieve more consistent feedfactors over the refill range.

Input range: Display only [MF@100%DC]

«
...
17
18
19
20
21
...
»

Содержание KSU-II/KCM


























































































































Отзывы:

Нет отзывов

Похожие инструкции для KSU-II/KCM

Бренд: Falcon Страницы: 3

Бренд: Rain Bird Страницы: 48

Бренд: Daikin Страницы: 2

Бренд: Daikin Страницы: 12

Бренд: Daikin Страницы: 12

Бренд: Daikin Страницы: 46

Бренд: Daikin Страницы: 21

Бренд: Daikin Страницы: 20

Бренд: Samson Страницы: 73

Бренд: Harsco Industrial Страницы: 57

Бренд: jbc Страницы: 44

Бренд: jbc Страницы: 8

Бренд: Balboa Страницы: 74

Бренд: Cadac Страницы: 4

FSDrive-MV1000 Series

Бренд: YASKAWA Страницы: 260

Бренд: YASKAWA Страницы: 114

Бренд: YASKAWA Страницы: 20

Бренд: YASKAWA Страницы: 152

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды