K-TRON KSU-II/KCM страница 55 Скачать руководство пользователя

Страница: 55 / 121

Docu-No.: 0590020601-EN Rev. 1.6.0

Page 55

Programming Reference

Loader menu 1.9

1.9

Loader menu

This menu programs the vacuum loader function. No HCU is required.
See section

5.2

for more information on loader applications.

Notes:

• In later KCM S/W versions 1.3 and later, this menu will be hidden if

an HCU is connected to the KCM.

• Be sure the parameter <LOADER FUNCTION> in this menu is

<Disabled> if a loader with HCU control is to be used.

1.9.1

Loader parameters

Parameter

Definition

LOADER FUNCTION

Loader Function

Selects whether loader runs or not. Select <KCM IO> or
<EXTERNAL> to run, <OFF> to stop.

MAX LOAD TIME

Max Load Time

Load time in seconds to reach the high level proximity sensor. An
alarm will occur if the high level is not reached in this time.

Default: 30 seconds

SHUTDOWN TIME

Shutdown Time

Time, in seconds, for the motor to wind down at the end of the load
cycle.

Default: 5 seconds

DISCHARGE TIME

Discharge Time

Time, in seconds, it takes to discharge the loader contents.

Default: 10 seconds

VALVE CLOSE TIME

Valve Close Time

Time, in seconds, it takes for the discharge valve to close at the end
of a discharge.

Default: 5 seconds

Содержание KSU-II/KCM


























































































































Результаты поиска

Содержание KSU-II/KCM

Отзывы:

Похожие инструкции для KSU-II/KCM

Бренды по названию

Популярные бренды

K-TRON KSU-II/KCM, Инструкция по программированию

Результаты поиска

Содержание KSU-II/KCM

Отзывы:

Похожие инструкции для KSU-II/KCM

Бренды по названию

Популярные бренды