manualshive.com logo in svg

Juniper JUNOSE 11.2.X BGP AND MPLS, Руководство по настройке

Конфигурационное руководство для Juniper JUNOSE 11.2.X по настройке BGP и MPLS. Получите доступ к бесплатному скачиванию этого руководства на нашем сайте. Подробная информация о настройке и использовании продукта доступна для загрузки на manualshive.com.

Поделиться
Скачать
background image

MPLS ping feature

data plane failure detection for egress nodes

IP address in echo request matching with

interface IP address.......................................247

IP address in echo request not matching

with interface IP address.............................247

detection of plane failures

in point-to-multipoint MPLS LSPs at

egress nodes....................................................246

in point-to-multipoint LSPs

type value for Echo Jitter TLV.........................247

P2MP Responder Identifier TLV

checking for receipt of......................................249

relation with traceroute requests

for point-to-multipoint LSPs.........................248

selecting the egress node for tracing path

using IPv4 Egress Address P2MP

Responder Identifier.....................................249

using IPv4 Node Address P2MP Responder

Identifier.............................................................249

using IPv6 Egress Address P2MP

Responder Identifier.....................................249

using IPv6 Node Address P2MP Responder

Identifier.............................................................249

testing connectivity in point-to-multipoint

LSPs, limitation

at branch nodes..................................................246
at ingress nodes..................................................246
at transit nodes...................................................246

using P2MP Responder Identifier TLV

no response to the originator..........................247
success response to the originator...............247

verifying connectivity at egress nodes in

point-to-multipoint LSPs

using Echo Jitter TLV.........................................246
using P2MP Responder Identifier

TLV.......................................................................246

using RSVP P2MP IPv4 Session

sub-TLV.............................................................246

mpls rsvp commands

mpls rsvp...............................................................279, 282
mpls rsvp authentication.........................................294
mpls rsvp authentication key.................................294
mpls rsvp bfd-liveness-detection........................300
mpls rsvp disable.........................................................282
mpls rsvp egress-router............................................279
mpls rsvp profile........................................279, 281, 282
mpls rsvp signalling hello.........................................297

mpls rsvp signalling hello graceful-restart

recovery-time...........................................................298

mpls rsvp signalling hello graceful-restart

restart-time...............................................................298

mpls rsvp signalling node-hello............................299

mpls-relay atm cell-packing mcpt-timers

command...........................................................................526

mpls-relay atm vpi-range command...........................526
mpls-relay command

prerequisite for configuring

cell concatenation parameters for ATM

ports....................................................................528

VCI/VPI range for ATM VCs

transmission.....................................................527

MTU problems

determining the exact LSR

where size of echo requests exceeds MTU

size.......................................................................379

troubleshooting and verifying in

MPLS LSPs with a Martini circuit..................379
MPLS LSPs with a VPLS instance................379
MPLS LSPs with an IP or IPv6

address...............................................................379

MPLS LSPs with an L3VPN or IPv6

address...............................................................379

MPLS LSPs with an RSVP-TE tunnel..........379

multicast IPv4 address family........................43, 150, 384
multicast IPv6 address family........................43, 150, 384
Multicast LDP FEC Stack sub-TLVs

in echo requests

and Egress Address P2MP Responder

Identifier sub-TLVs........................................250

and Node Address P2MP Responder

Identifier sub-TLVs........................................250

multiexit discriminator, BGP.................................................11
multihoming

for VPLS...........................................................................581

multiple ATM VCs transportation

over a single pseudowire

VPI/VCI ranges....................................................525

multiple ATM virtual circuits

transmission over a single pseudowire

ATMx port state...................................................526

Multiprotocol Label Switching.

See

MPLS

(Multiprotocol Label Switching)

multiservice layer 2 services..............................................515

697

Copyright © 2010, Juniper Networks, Inc.

Index

Содержание JUNOSE 11.2.X BGP AND MPLS







































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOSE 11.2.X BGP AND MPLS

Canon PowerShot A410 Software Starter Manual preview
PowerShot A410
Бренд: Canon Страницы: 106
MACROMEDIA FLASH 8-FLASH Tutorials Manual preview
FLASH 8-FLASH
Бренд: MACROMEDIA Страницы: 292
MACROMEDIA BREEZE 5 Manual preview
BREEZE 5
Бренд: MACROMEDIA Страницы: 26
MACROMEDIA BREEZE Installation Manual preview
BREEZE
Бренд: MACROMEDIA Страницы: 32
MACROMEDIA FIREWORKS 2-USING FIREWORKS Use Manual preview
FIREWORKS 2-USING FIREWORKS
Бренд: MACROMEDIA Страницы: 20
Tascam GigaStudio 3.04 Supplement Sheet preview
GigaStudio 3.04
Бренд: Tascam Страницы: 2
F-SECURE INTERNET GATEKEEPER WINDOWS 2000-2003 SERVER 6.61... Administrator'S Manual preview
INTERNET GATEKEEPER WINDOWS 2000-2003 SERVER 6.61...
Бренд: F-SECURE Страницы: 414
ScanSoft TextBridge PRO 8.5 User Manual preview
TextBridge PRO 8.5
Бренд: ScanSoft Страницы: 243
Altigen MaxACD Administrator Manual preview
MaxACD Administrator
Бренд: Altigen Страницы: 261
Juniper JUNOSE 11.2 Configuration Manual preview
JUNOSE 11.2
Бренд: Juniper Страницы: 772
Microtek ScanWizard Pro Reference Manual preview
ScanWizard Pro
Бренд: Microtek Страницы: 177
KAPERSKY ANTI-VIRUS 5.1 - FOR MICROSOFT ISA SERVER Administrator'S Manual preview
ANTI-VIRUS 5.1 - FOR MICROSOFT ISA SERVER
Бренд: KAPERSKY Страницы: 67
Red Hat ENTERPRISE LINUX WS 2.1 - Installation Manual preview
ENTERPRISE LINUX WS 2.1 -
Бренд: Red Hat Страницы: 110
Siemens OC130S Installation Instructions Manual preview
OC130S
Бренд: Siemens Страницы: 11
Siemens ID Mouse V 3.1 User Manual preview
ID Mouse V 3.1
Бренд: Siemens Страницы: 28
Siemens ROS User Manual preview
ROS
Бренд: Siemens Страницы: 32
Siemens OpenScape Xpressions PhoneMail User Manual preview
OpenScape Xpressions PhoneMail
Бренд: Siemens Страницы: 110
Apricorn SMART-ER User Manual preview
SMART-ER
Бренд: Apricorn Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды