manualshive.com logo in svg

Juniper JUNOSE 11.2.X BGP AND MPLS, Руководство по настройке

Конфигурационное руководство для Juniper JUNOSE 11.2.X по настройке BGP и MPLS. Получите доступ к бесплатному скачиванию этого руководства на нашем сайте. Подробная информация о настройке и использовании продукта доступна для загрузки на manualshive.com.

Поделиться
Скачать
background image

documentation set

comments on...............................................................xxxv

domain, VPLS........................................................................574
domain-id command.........................................................486
domain-tag command......................................................486
dont-install-routes command.......................................484
DS-BGP routers.....................................................................476
dual-stack BGP routers......................................................476
dynamic capability negotiation.......................................123
dynamic interfaces, created by MPLS..........................229
dynamic peering, BGP...........................................................43
dynamic peers, remove BGP..............................................43
dynamic route redistribution, disabling in BGP...........54
dynamically learned defaults.............................................55

E

E-LSP................................................................................212, 307
EBGP (external Border Gateway Protocol)

updates in indirectly connected networks............32

Echo Jitter TLV

contained in echo responses

no action taken....................................................248

detecting data plane failures

at egress nodes in point-to-multipoint

MPLS LSPs.......................................................246

functions of

beneficial when the entire LSP tree is

pinged.................................................................248

preventing flooding of responses.................248
segregating echo responses from multiple

egress nodes....................................................248

invalid in echo responses.........................................248
not contained in echo requests

no delay in echo responses............................248

preconfigured value, default...................................248
supported delay period

exceeded, alternative action taken..............247
maximum value..................................................248
of up to 30 seconds...........................................247

to process MPLS LSP ping messages

delaying the sending of echo

responses...........................................................247

type value defined in

IETF draft, Detecting Data Plane Failures

in Point-to-Multipoint Multiprotocol
Label Switching (MPLS) - Extensions to
LSP Ping ............................................................247

type value, 12.................................................................248

used in MPLS echo request packets

delay the sending of echo responses..........247

uses

preventing echo responses from being

discarded...........................................................248

preventing flooding of responses at ingress

nodes..................................................................248

echo reply packets, MPLS.................................................244
echo request packets, MPLS...........................................244
ECMP (equal-cost multipath)

BGP...................................................................................439
BGP/MPLS VPNs..............................................384, 439
MPLS indirect next hops..........................................384
path failures in BGP/MPLS VPNs..........................384
pruning failed paths...................................................384

Egress Address P2MP Responder Identifier

sub-TLVs

specifying

IPv4 address of egress nodes........................250
IPv6 address of egress nodes........................250

used to denote

a specific egress node from which path

must be traced................................................250

enable a protocol

BGP routing.............................................................18, 439

enable protocols

BGP routing...................................................................656

encapsulations

ATM AAL0.......................................................................518
ATM AAL05....................................................................516

equal-cost multipath support on MPLS......................242
Ethernet aggregation and Martini layer 2

transport.............................................................................539

Ethernet raw mode encapsulation

overview..........................................................................522

Ethernet/VLAN over MPLS (Multiprotocol Label

Switching)

configuration steps.....................................................533
overview.........................................................................509

exit-address-family

command.......................................46, 152, 444, 596, 657

explicit null label, advertise the......................................220
export map

setting the BGP/MPLS VPN....................................428
use......................................................................................431

export map command........................................................431
extended communities

BGP...............................................................................12,  95
route target....................................................................389

689

Copyright © 2010, Juniper Networks, Inc.

Index

Содержание JUNOSE 11.2.X BGP AND MPLS







































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOSE 11.2.X BGP AND MPLS

Samsung UN40C7000WF User Manual preview
UN40C7000WF
Бренд: Samsung Страницы: 7
Yamaha DM 1000 Manual preview
DM 1000
Бренд: Yamaha Страницы: 30
VMware VCENTER CHARGEBACK 1.5 - API Manual preview
VCENTER CHARGEBACK 1.5 - API
Бренд: VMware Страницы: 150
COMPRO COMPRODVD2 User Manual preview
COMPRODVD2
Бренд: COMPRO Страницы: 18
Sigma PHOTO PRO 4.2 Manual preview
PHOTO PRO 4.2
Бренд: Sigma Страницы: 55
Red Hat JBoss Developer Studio 3.0 User Reference Manual preview
JBoss Developer Studio 3.0
Бренд: Red Hat Страницы: 78
Pioneer CNSD-239FM Upgrade Instructions And Operation Manual Addendum preview
CNSD-239FM
Бренд: Pioneer Страницы: 28
Pioneer CNSD-230FM Upgrade Instructions And Operation Manual Addendum preview
CNSD-230FM
Бренд: Pioneer Страницы: 28
Blackberry MEDIA SYNC Release Note preview
MEDIA SYNC
Бренд: Blackberry Страницы: 9
Blackberry ENHANCED GOOGLE MAIL PLUG IN - LEARN MORE User Manual preview
ENHANCED GOOGLE MAIL PLUG IN - LEARN MORE
Бренд: Blackberry Страницы: 16
Blackberry PRD-10459-003 - Enterprise Server For IBM Lotus Domino Administration Manual preview
PRD-10459-003 - Enterprise Server For IBM Lotus Domino
Бренд: Blackberry Страницы: 420
Garmin GPSMAP GPSMAP 196 Specifications preview
GPSMAP GPSMAP 196
Бренд: Garmin Страницы: 2
Garmin MapSource User Manual preview
MapSource
Бренд: Garmin Страницы: 32
Juniper VXA2000 Series Quick Start Manual preview
VXA2000 Series
Бренд: Juniper Страницы: 14
3Com 3C19250 - USB Ethernet Network Interface Card User Manual preview
3C19250 - USB Ethernet Network Interface Card
Бренд: 3Com Страницы: 16
Intel IT DIRECTOR Manual preview
IT DIRECTOR
Бренд: Intel Страницы: 43
Z3 Technology Z3-DM368-APP Manual preview
Z3-DM368-APP
Бренд: Z3 Technology Страницы: 8
MACROMEDIA FLASH 8-FLASH Use Manual preview
FLASH 8-FLASH
Бренд: MACROMEDIA Страницы: 678

Бренды по названию

Популярные бренды

Загрузить еще бренды