manualshive.com logo in svg

Juniper JUNOSE 11.2.X BGP AND MPLS, Руководство по настройке

Конфигурационное руководство для Juniper JUNOSE 11.2.X по настройке BGP и MPLS. Получите доступ к бесплатному скачиванию этого руководства на нашем сайте. Подробная информация о настройке и использовании продукта доступна для загрузки на manualshive.com.

Поделиться
Скачать
background image

pseudowires

associating an ATM port with

before configuring cell

concatenation.................................................528

before configuring VCI/VPI ranges..............528

configuration on both ends of the

matching in the VP/VCI range........................525
not matching in the VPI/VCI range..............525

failure detection

change of state on the ATMx port...............526

multiple ATM virtual circuits

and emulation of connectivity between

two ATM ports.................................................524

transportation of multiple ATM virtual circuits

over a single wire.................................................524

using a single wire for multiple VCs transport

topology example..............................................559

PWid FEC element TLV, for VPLS with LDP

signaling..............................................................................580

R

rd command...........................................................................424
reachability

verify and troubleshoot MPLS................................244

reconvergence of BGP/MPLS VPN networks,

fast........................................................................................454

redistribute command..........................................................54
redistribution routes

disable dynamic (BGP)...............................................54

refresh messages, MPLS...................................................240
refresh-period command.........................................279, 281
remote-neighbor command............................................484
reoptimization and backup...............................................252
reset BGP sessions................................................................96
Response Type field

contained in echo requests

echo response from egress nodes...............249
without P2MP Responder Identifier TLV in

echo requests..................................................249

controlling MPLS echo responses........................250

RFC 4364—BGP/MPLS IP Virtual Private Networks

(VPNs) (February
2006)....................................15, 216, 393, 402, 405, 408

RFC 4816—Pseudowire Emulation Edge-to-Edge

(PWE3) Asynchronous Transfer Mode (ATM)
Transparent Cell Transport Service (February
2007)......................................................................................511

RIB (routing information base)

core non-VPN RIB.......................................................430
core VPN RIB.................................................................430
disabling RIBs-Out........................................................34

rib-out disable command....................................................43
route distinguisher...............................................................389
route interface command..............................531, 532, 538

prerequisite for configuring

cell concatenation parameters for ATM

ports....................................................................528

route interface tunnel command

prerequisite for configuring

VCI/VPI range for ATM VCs

transmission.....................................................527

route maps, BGP.......................................................................71

assigning neighbor weights.......................................110
filtering incoming/outgoing routes..........................88
setting local preferences............................................114

route reachability information, BGP/MPLS

VPN........................................................................................413

route reflectors.......................................................................145
route target

defining BGP/MPLS VPN..........................................425

route targets

configuring VPN topologies....................................409
export list.......................................................................389
for VPN topologies.....................................................409
import list.......................................................................389

route- refresh message , BGP...............................................8
route-map command............................................................75
route-refresh capabilities...................................................123
route-target address family......................................43, 384
route-target command......................................................425
route-target extended community.................................413
route-target filtering, advertisement rules

with.........................................................................................413

route-target filters.................................................................413
route-target membership attribute................................413
router commands

router bgp...........................................18, 439, 596, 656
router ospf.....................................................................604

routes

BGP........................................................................................9
conditionally advertising BGP....................................61
processing of received routes for BGP/MPLS

VPNs............................................................................459

redistributing into BGP.................................................53
using BGP........................................................................153

routing and forwarding instance.

See

VRF

701

Copyright © 2010, Juniper Networks, Inc.

Index

Содержание JUNOSE 11.2.X BGP AND MPLS







































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOSE 11.2.X BGP AND MPLS

Barracuda Networks NG Network Access Client SP4 Administrator'S Manual preview
NG Network Access Client SP4
Бренд: Barracuda Networks Страницы: 268
TANDBERG Codian Remote Management API Reference Manual preview
Codian Remote Management API
Бренд: TANDBERG Страницы: 66
Nortel Quality Monitoring Reference Manual preview
Quality Monitoring
Бренд: Nortel Страницы: 22
AVIRA SECURITY MANAGEMENT CENTER 2.5 Manual preview
SECURITY MANAGEMENT CENTER 2.5
Бренд: AVIRA Страницы: 39
KAPERSKY ANTI-VIRUS - FOR FREEBSD-OPENBSD-BSDI MAIL SERVER User Manual preview
ANTI-VIRUS - FOR FREEBSD-OPENBSD-BSDI MAIL SERVER
Бренд: KAPERSKY Страницы: 295
National Instruments PID Control Toolkit 371685C-01 User Manual preview
PID Control Toolkit 371685C-01
Бренд: National Instruments Страницы: 39
Creative Platinum eX User Manual preview
Platinum eX
Бренд: Creative Страницы: 84
Red Hat DEVICE-MAPPER MULTIPATH 4.6 Configuration And Administration Manual preview
DEVICE-MAPPER MULTIPATH 4.6
Бренд: Red Hat Страницы: 42
Konica Minolta COLIBRI Brochure preview
COLIBRI
Бренд: Konica Minolta Страницы: 6
Multitech FaxFinder V.34 User Manual preview
FaxFinder V.34
Бренд: Multitech Страницы: 96
Applied Biosystems Data Explorer 4 Series User Manual preview
Data Explorer 4 Series
Бренд: Applied Biosystems Страницы: 447
Intel 2521131 - Intel Wasp Motherboard Quick Start Manual preview
2521131 - Intel Wasp Motherboard
Бренд: Intel Страницы: 1
UNIBLUE PowerSuite 2010 Product Manual preview
PowerSuite 2010
Бренд: UNIBLUE Страницы: 13
DigiDesign Trillium Lane Labs Manual preview
Trillium Lane Labs
Бренд: DigiDesign Страницы: 114
LEI accessories MAPCREATE 7 Installation And Operation Instructions Manual preview
MAPCREATE 7
Бренд: LEI accessories Страницы: 116
Native Instruments Deep Freq Manual preview
Deep Freq
Бренд: Native Instruments Страницы: 50
IBM VIAVOICE-SIMPLY DICTATION FOR MAC OS X User Manual preview
VIAVOICE-SIMPLY DICTATION FOR MAC OS X
Бренд: IBM Страницы: 92
Mackie Final Mix VST Manual preview
Final Mix VST
Бренд: Mackie Страницы: 26

Бренды по названию

Популярные бренды

Загрузить еще бренды