Jungheinrich EJE 116, Руководство по эксплуатации

Страница: 46 / 81

E 17
0606
.GB
5.5 Travel parameters
Z
For trucks without indicator instrument (CANDIS (
o
)) the code lock parameters can
only be set by the manufacturer's service.
The following example shows the parameter setting for the acceleration of travel pro-
gram 1 (parameter 101).
Acceleration example
– Enter the three-digit parameter number (101) and confirm with the Set key (16).
– Check the LC display of the indicator instrument (CANDIS (
o
)) (parameter number
and current parameter value are displayed).
Z
If there is no input for approx. 5 seconds, the display switches back to operating hours
indication.
F
If another parameter number than the one displayed is desired, you must wait until
the operating hours are displayed again.
– Enter or change the parameter value according to the parameter list.
– Check the LC display of the indicator instrument (CANDIS (
o
))(confirm with the Set
key (16)).
– The LED (15) of the
o
-key (20) switches briefly to steady light and start flashing
again after approx. 2 seconds.
Z
When the input is incorrect, the LED (15) of the
o
-key (20) lights up red. After enter-
ing the parameter number again, the setting value can be entered or changed.
Repeat the procedure to enter further parameters as soon as the LED (15) of the
o
-
key (20) flashes. To terminate the input, press the
o
-key (20).
Z
During the parameter input the travel function is switched off. If the setting value is to
be checked in travel operation, follow this sequence:
– Select the modified travel programme after entering the parameter value, confirm
with the Set key (16).
– The truck is now in travel operation and can be checked.
– To continue the setting operation, confirm with the Set key (16) again.
Display instrument
(CANDIS)
LED (15)
o
-key
LED (17)
Key 1
LED (18)
Key 2
LED (19)
Key 3
current setting is
displayed
101 6
green
flashing
off off off
changed setting
is displayed
101 8
green
flashing
off off off
Parameter
number
Parame-
ter setting
value
E 17
0606
.GB
5.5 Travel parameters
Z
For trucks without indicator instrument (CANDIS (
o
)) the code lock parameters can
only be set by the manufacturer's service.
The following example shows the parameter setting for the acceleration of travel pro-
gram 1 (parameter 101).
Acceleration example
– Enter the three-digit parameter number (101) and confirm with the Set key (16).
– Check the LC display of the indicator instrument (CANDIS (
o
)) (parameter number
and current parameter value are displayed).
Z
If there is no input for approx. 5 seconds, the display switches back to operating hours
indication.
F
If another parameter number than the one displayed is desired, you must wait until
the operating hours are displayed again.
– Enter or change the parameter value according to the parameter list.
– Check the LC display of the indicator instrument (CANDIS (
o
))(confirm with the Set
key (16)).
– The LED (15) of the
o
-key (20) switches briefly to steady light and start flashing
again after approx. 2 seconds.
Z
When the input is incorrect, the LED (15) of the
o
-key (20) lights up red. After enter-
ing the parameter number again, the setting value can be entered or changed.
Repeat the procedure to enter further parameters as soon as the LED (15) of the
o
-
key (20) flashes. To terminate the input, press the
o
-key (20).
Z
During the parameter input the travel function is switched off. If the setting value is to
be checked in travel operation, follow this sequence:
– Select the modified travel programme after entering the parameter value, confirm
with the Set key (16).
– The truck is now in travel operation and can be checked.
– To continue the setting operation, confirm with the Set key (16) again.
Display instrument
(CANDIS)
LED (15)
o
-key
LED (17)
Key 1
LED (18)
Key 2
LED (19)
Key 3
current setting is
displayed
101 6
green
flashing
off off off
changed setting
is displayed
101 8
green
flashing
off off off
Parameter
number
Parame-
ter setting
value