JR ProPo xg8 Скачать руководство пользователя страница 92

Страница: 92 / 92

Repairs and After-Sales Service

When Required...

Only when the product is faulty after normal operation

within the warranty period, we will repair the product for

free based on our regulations. The repair will be paid for by

the consumer when the damage is due to use in improper

ways (i.e., damages due to failure in operation, misuse etc.)

or beyond the warranty period, or without the warranty

attached (Copies will not be accepted). Note that some

damages may not be economically repairable.

The scope of the warranty is limited to the Proportional

Radio System and excludes aircrafts, engines and any other

non JR product.

Please note beforehand that we will not be responsible for

any damage to the data which was set or recorded by the

customer/the third person, data loss, damage caused by

missing an opportunity of the product use, nor for any

compensation for damage to human life, health or

property, nor for any damage incidental to the above.

When the warranty period has expired, we will repair the

product for cost if requested by the customer and if we

judge that the product may be continuously/safely used

after repairing.



Please note in advance that the warranty period may

vary depending on each JR Sales Agent (JR Distributor)

in your country. Please contact them for further details

concerning the warranty or After-Sales Service (i.e.

Repair services, purchase of parts and/or the accesso-

ries).

Please save the preset data on a data sheet or on a SD card,

before requesting any repair.

The product may be initialized during the repair as

needed. We will not be responsible for any damage or loss

of data set by customers.

1. This product and the associated documents are copyrighted by Japan Remote Control Co., Ltd.

It is prohibited by law to duplicate, copy, reprint, or modify the product/documents, either entirely or

partially without prior notice and approval.

2. This product is not designed to be used as equipment or as an instrument which involves human life

including purposes for medical instrument, aerospace instrument, transport equipment, and weapon

system, or any other purpose in which high reliability is required, such as space satellite use. We will not

be responsible for physical injury, ﬁre, or any other social damage arising from the improper use of this

product in any of the equipment or equipment control systems of the general type as described (but

not limited to) above.

3. The product and the contents in the document are subject to change without prior notice due to ongo-

ing development.

4. If customers violate any of the terms listed in



Caution



of this document, customers shall terminate

the use of the product if ordered by our company.

5. Please note that regardless of the above, we will not be responsible for any other eﬀects which arise by

operating the product.



Caution



Be sure to read the warranty.



Preset Data

Содержание xg8





























































































Результаты поиска

Содержание xg8

Отзывы:

Бренды по названию

Популярные бренды

JR ProPo xg8, Руководство по эксплуатации

Результаты поиска

Содержание xg8

Отзывы:

Бренды по названию

Популярные бренды