JR ProPo xg8 Скачать руководство пользователя страница 29

Страница: 29 / 92

THROTTLE TRIM

Each Function in the Function List

Function Explanation

This function sets the Throttle Trim movement, and a Throttle Cut function is provided for cutting the

engine. There is a Trim Memory function for cutting the engine using the Trim.

Note that for airplanes, an Idle Adjust function is also incorporated that allows separate detailed setting of

the idling position.

•

Setting Method

The Cut function can be used only with either the Throttle Cut or the Trim Memory. If the Throttle Cut is set

to ACT, the Trim Memory will be forcibly set to INH. On the screen rotate the dial to move to and select the

setting item (inverse display), then press the dial to set the item. Note that an Idling Adjust function that

allows setting of Idle Up and Down for airplane models will be shown on Page 3.

•

Please carefully conﬁrm whether the linkage will lock when the carb is closed.

The switch names on the Switch Selection screen will diﬀer slightly according to the model type.

•

Hints

【THRO TRIM】

●Throttle Cut Screen (Page 1)

If the function is set to ON and the stick is lowered, the carb will close and the servo will move to reach the set position.

●Trim Memory Screen (Page 2)

When the Trim is lowered in a single action, the trim position immediately prior to the movement will be memorized,

and when the trim is raised again, the trim will momentarily return to the memorized position. The memorized position

will be marked on the Trim display.

Caution Item

Helicopter

Airplane

●Idling Adjustment Screen (Page 3)

The idling position during Stick Slow can be given separate detailed settings using the switches.

Operation Condition in this Function

Idling Position Adjustment

In order to use the function, after setting

the Throttle Cut function to INH, set the

Trim Memory to ACT in this function.

Throttle Cut will only be effective in the situation where the Flight Mode in a helicopter has been set to

“NORMAL”.

Function Operation Condition

In order to use the function,

INH should be changed to ACT.

Position that has been Set

Adjust this to

the position

where the carb

will close.

The Switch Operation

Time Lag can be set.

To the Switch

Setting Screen

To the Switch

Setting Screen

Because this function will be prioritized when Throttle Cut is

set to ACT, the Trim Memory on Page 2 cannot be set to ACT.

Содержание xg8





























































































Результаты поиска

Содержание xg8

Отзывы:

Бренды по названию

Популярные бренды

JR ProPo xg8, Руководство по эксплуатации

Результаты поиска

Содержание xg8

Отзывы:

Бренды по названию

Популярные бренды