JR ProPo xg8 Скачать руководство пользователя страница 6

Страница: 6 / 92

Lock

Unlock

Stick Head Adjustment

Rotate the hollow (set) screw located at the

tip of the stick head to unlock, and rotate the

entire stick to adjust to the desired length.

When ﬁnished, lock it again with the hollow

(set) screw.

Model Type Sticker

First, affix the sticker of your preferred model

type. Remove any dust from the affixing surface,

then detach the sticker from the backing paper.

Next, apply the sticker to the trans-

mitter surface, carefully matching

the edges with the sticker area

marked on the transmitter.

Hook Holder

For long ﬂights you may choose

to use a neck strap.

SD Card Mounting and Removing Methods

SD Cards that can be used are cards of 16GB or less in size that have been formatted in FAT format.

Mounting and removing SD cards should be carried out after opening the battery cover. The SD card slot is located below

the battery.

Further, among the SD cards that are available, some types cannot be used. Please use the JR-SDM2G SD card (sold sepa-

rately).

Regarding the Handling of the Rechargeable Ni-MH Batteries used in the Receiver

Preparation

Because nickel metal hydride batteries have a high self-discharge rate, battery discharge will gradually take place even when

the battery is not being used.

For new batteries and batteries that have not been used for a long time, be certain to carry out charging before use.

In addition, if repeak is repeatedly carried out (charging carried out when the battery has only discharged by a small amount),

the battery characteristics will mean that the discharge voltage will be temporarily reduced, and a memory eﬀect may be

incurred that will shorten the battery usage time. In this situation, it is recommended that you discharge the battery power

once then recharge it before use. Carrying out recharging at high temperatures and low temperatures will be dangerous.

According to the battery characteristics, the charging of nickel metal hydride batteries at high temperatures will cause a

noticeable drop in the charging amount. Do not carry out charging inside a car. Further, hydrogen gas may be generated

during charging and discharging. Be absolutely certain to avoid carrying out charging close to ﬁre.

Mounting Method

Switch oﬀ the transmitter,

then slowly insert the SD

card into the slot taking

care of the card direction

until you feel a “click”.

Removing Method

Lightly press in

the middle of the

SD card, then

slowly take out

the card which will

pop out when you

remove your

ﬁnger.

Содержание xg8





























































































Результаты поиска

Содержание xg8

Отзывы:

Бренды по названию

Популярные бренды

JR ProPo xg8, Руководство по эксплуатации

Результаты поиска

Содержание xg8

Отзывы:

Бренды по названию

Популярные бренды