JR ProPo xg8 Скачать руководство пользователя страница 38

Страница: 38 / 92

AILERON → RUDDER MIXING

Each Function in the Function List

Function Explanation

This function allows smooth correction of turning for scale model aircraft. It will be possible to

link the rudder operation using the aileron operation. In addition, in glider models a Brake func-

tion is also provided that automatically releases this mixing by rudder and elevator operation.

•

Setting Method

The left side of the display shows the current Flight Mode (only when settings have been made)

and the left and right linked movement amounts.

Rotate the dial to move to the item on the screen that can be set (inverse display) and select it.

Then press the dial to display the setting box and carry out setting of the item.

•

【AILE→RUDD】

Actually operate the servos and carefully confirm the settings before flying.

Caution Items

There are also Brake Point settings on the right side of the screen for releasing this mixing

using stick operation.

Airplane

Glider

●Screen for Airplanes

Switch Setting Screen

●Screen for Gliders

(The screen also displays the current Flight Mode)

Current Flight Mode

This sets the range

of the Brake

movement.

Conﬁrm and set the previous

polarity of the ﬁgures using

the actual servo movement.

Linked Movement

Amounts to the Left

and Right

Linked Movement Amounts

to the Left and Right

This sets the Function to

ON/OFF using the

Switches

Brake Setting Screen

Содержание xg8





























































































Результаты поиска

Содержание xg8

Отзывы:

Бренды по названию

Популярные бренды

JR ProPo xg8, Руководство по эксплуатации

Результаты поиска

Содержание xg8

Отзывы:

Бренды по названию

Популярные бренды