JR ProPo xg8 Скачать руководство пользователя страница 11

Страница: 11 / 92

Concerning the connection and incorporation of

the servos and the power source

Receiver Connection

Preparation

Since the receiver is susceptible to vibration, shock, and water,

anti-vibration and waterprooﬁng measures should be securely

implemented.

•

If the connectors become detached while ﬂying, there will be a

risk of uncontrolled operation. Please securely insert all of the

connectors as far as they will go.

•

In the situation where relay connectors (extension leads) are

used during the installation rubber sponge should be wrapped

round the connectors to ﬁx them.

Be absolutely sure not to leave the connectors hanging

unsupported.

•

In JR receivers, the channels for connecting servos are given names rather than numbers.

From this point onward in the manual the receiver channels are described using their names, so be careful of this when reading the manual.

Concerning the 2.4GHz Band Characteristics and Receiving Radio Wave

Weak

Signal

Strong

Reception

Strong

Reception

The antenna part (30mm) should be installed

perfectly straight. If bent, stable receiving will

not be possible.

Material Frame

Receiving

Sensitivity

(Low)

Receiving

Sensitivity

(High)

Receiving Sensitivity (High)

Wrong Antenna Installation

The arrows show the receiving direction with

regard to the antenna.

RG Cable 150

RG831B Main Unit

Remote Antenna

Built-in Anten

▼

Front Face

▲

Rear Face

Strong

Reception

Strong

Reception

Weak

Signal

RA01T Side View

DO NOT bend the antenna tip !

Built-in Antenna

Circuit Board Face

Due to the 2.4GHz band which has a strong directionality in

its radio waves, the receiving sensitivity will greatly diﬀer

depending on the direction against the antenna. Since the

antenna receives radio waves from the sides rather than

from the tip, please take adequate care of the antenna

direction when installing the antenna in the model.

In the case where there are two coaxial antennas in the receiver

main unit, the faces of each antenna should be installed so that

they are at right angles to each other, rather than being parallel.

Note that in order to allow certain and stable communications to

be carried out, it is recommended that each antenna should be

installed with a separation of 30mm or more.

If each antenna is installed in parallel, the

receiving eﬃciency will be reduced.

The built-in antenna of the remote antenna is

installed on the surface of the circuit board.

Care will be required in the situation where the

built-in antenna has been installed beside a

shielding material, since the receiving

sensitivity will be considerably degraded.

* The remote antenna receives the data and also

feeds back to the transmitter.

The antenna part should be installed

in a perfectly straight condition.

Coaxial part of the antenna can

be bent however, do not bend it

in a right angle. This will damage

the internal antenna wires.

In the situation where the antenna has been

attached directly to a shielding material such

as carbon or metal, the receiving sensitivity

of the installed antenna surface will be

considerably reduced. When the antenna is

to be installed on this kind of shielding

material, either separate the antenna as far

as possible from the material, or in the case

where the radio wave shielding material is

the aircraft body itself project the antenna

outside the aircraft body.

* Take care not to

damage the

antennas

projecting from the

aircraft body.

Aircraft body surface made from

shielding material.

* When using a gyro, carry out the

connection according to the gyro

operation manual.

Receiver Battery

BIND PLUG

Rudder Channel

Gyro Sensitivity

Adjusting Channel

Auxiliary Channel

Binding Plug

Sensor

Y-Harness

Switch

Harness

Auxiliary Channel

Elevator Servo

Aileron Servo

Throttle Servo

SENSOR

Insert the connector,

taking adequate

care of the

direction.

This is used when

setting the binding

For connecting the

sensor,connect the

Y-Harness (sold

separately) to the

[BIND/BATT/SENS]

terminal.

Содержание xg8





























































































Результаты поиска

Содержание xg8

Отзывы:

Бренды по названию

Популярные бренды

JR ProPo xg8, Руководство по эксплуатации

Результаты поиска

Содержание xg8

Отзывы:

Бренды по названию

Популярные бренды