JR ProPo xg8 Скачать руководство пользователя страница 3

2

About the Proportional System

Basic Precautions for Safe Use 

of the 2.4GHz System

Please understand that this company cannot be 

responsible for any accident or failure that may 

occur from the modification of this product, use of 

non-genuine parts, natural disaster, or non-

observance of the precautions described in this 

manual. Further, as for damages caused by an acci-

dent or failure, please understand that items (such 

as airplanes, competitorsʼ products, fuel, etc.) 

excepting this product and this Companyʼ s genuine 

parts will not be covered under the warranty.

The use of radio waves required in this product is 

defined as follows in the Radio Law of Japan.

Indications and Symbols relating to Safety

This indicates actions that must 

be implemented.

This indicates actions that 

are forbidden.

The following symbols stated in this manual indicate the 

precautions regarding possible danger which may occur 

caused by improper handling.

Be sure to strictly observe them, as they contain impor-

tant safety instructions.

How to Handle

Before starting use, make sure that all the parts are 

provided. Then, connect the switch harness and servo to 

t h e   r e c e i v e r ,   a n d   i n s e r t   b a t t e r i e s   i n t o   t h e  

transmitter/receiver. Turn on the transmitter/receiver and 

confirm that they operate correctly. If they do not operate, 

check the batteries. If a rechargeable battery is used for 

the first time after purchase or is used after being left 

unused for a long period, be sure to charge it with the 

battery charger before use.

In the event of any missing parts, malfunction, etc., please 

contact the Service Section of this Company.

If incorrect operation methods are used, it is possible 

that there will be a danger of death or serious injury.

If incorrect operation methods are used, it is possible 

that there will be a possibility of death or serious injury.

If incorrect operation methods are used, it can be expected 

that there will be a possibility of problems occurring. 

Out-of-control  and  dangerous  situations  can  be 

caused.

DO  NOT  use  the  product  on  rainy  days  since  it  may 

cause  malfunction  if  water  gets  inside  the 

transmitter/receiver. If it should be used by necessity, 

make sure to take waterproof measures.

Injury due to heat generation, fire, or electric shock can 

occur.

Never disassemble or modify this product.

The  engine  and  the  motor  (in  the  case  of  an 

electrically-driven  model)  can  start  rotating  at  high 

speed, causing danger.

When turning on the power switch, set the transmitter 

throttle stick to the lowest speed position (where the 

engine/motor rotation does not become high) and turn 

on  the  transmitter  power  switch  and  the  receiver 

power switch in this order.

For  turning  off  power,  turn  off  the  receiver  and  the 

transmitter in this order.

Injury can be caused.

When adjusting the engine (motor), fully pay attention 

to the power which comes from the rear side.

DO NOT start the engine with the transmitter throttle in 

a high speed position. This is very dangerous.

The 2.4GHz band is not a frequency exclusively 

for use with RC airplanes. This frequency band is 

in common use with the ISM (industry, science, 

and medical care) band which is widely used for 

short-distance transmission such as microwave 

ovens, wireless LAN, digital cordless phones, 

audio games, cellphone Bluetooth, and VICS. 

Therefore, the steering response of the 2.4GHz 

system may be degraded in an urban area. 

Further, as it is also used for ham and local area 

radio communications for mobile identification, 

please pay attention to possible influences from 

these. In the event of any adverse radio wave 

interference on an existing wireless station, 

immediately stop emitting radio waves and take 

interference avoidance measures.

At a race track/airport, minimize use of a device 

that can affect the transmitter/receiver and be 

sure to confirm the safety beforehand. Also, 

always follow instructions given by the facility 

staff.

If an aircraft is allowed to fly behind a building, a 

pylon, trees, etc. so that the radio-wave range is 

blocked, the steering response may drop, even 

resulting in an “out-of-control” situation. Always 

let the aircraft fly within a range that can be visu-

ally observed.

General Precautions for Safety

It is very important to ensure that you 

observe the following precautions.

Introduction

 DANGER

WARNING

WARNING

CAUTION

●When this product is used overseas, authorization by 

the law of the country will be required.

●When this product is used overseas for a purpose 

other than as a model, it may be subject to the restric-

tions in accordance with the Export Trade Control 

Order. In such a case, an export permit under the 

Order is required.

Prohibited

Obligatory

Содержание xg8





























































































Отзывы: