JR ProPo xg8 Скачать руководство пользователя страница 16

Страница: 16 / 92

FLIGHT MODE

Function Common to All Models

Function Explanation

The Flight Mode function allows switching between the various aircraft settings in a one-touch operation

using the switches.

This means it will be possible to switch the aircraft ﬂight characteristics using one-touch operation.

•

Items that can be Changed in the Flight Mode

Basically, this function displays each of the Digital Trim positions and the settings in each of the function

screens in Function List using [SW SEL].

•

The ﬂight modes that can be switched consist of a maximum of six ﬂight modes of helicopters, up to three

ﬂight modes of airplanes, and a maximum of 5 ﬂight modes of gliders.

•

The current Flight Mode will be displayed on the Initial INFO screen, where it can be conﬁrmed. In addition,

it will also be possible to change the displayed name using the Flight Mode Name screen in the System List.

•

The displayed names in each Flight Mode will be diﬀerent for airplanes, helicopters, and gliders.

•

At the time of shipment, the Flight Mode switches in the airplane and glider models are not set.

Set the switches allocated in the Flight Mode using the Device Select screen.

Hint

Helicopter

Airplane

Glider

Current Flight Mode

Important

Содержание xg8





























































































Результаты поиска

Содержание xg8

Отзывы:

Бренды по названию

Популярные бренды

JR ProPo xg8, Руководство по эксплуатации

Результаты поиска

Содержание xg8

Отзывы:

Бренды по названию

Популярные бренды