jotron 103660 Скачать руководство пользователя страница 40

Страница: 40 / 104

Doc. No.: 103839 Rev. A

jotron.com

Page 40 of 104

8.1.3.1

GPS Antenna

When selecting a mounting location for the antenna, keep in mind the following points.

Select a location out of the radar beam. The radar beam will obstruct or prevent reception of the GPS

satellite signal.

There should be no interfering object within the line-of-sight to the satellites. Objects within the line-

of-sight to a satellite, for example a mast, may block reception or prolong acquisition time.

Mount the antenna unit as high as possible to keep it free of interfering objects and water spray,

which can interrupt reception of GNSS satellite signal if the water freezes.

The Transponder is delivered as standard with a Sanav SA-200 GPS

antenna with stainless steel stand and 15 meter cable with TNC

connectors in both ends for direct connection between

transponder and antenna.
The antenna can be mounted with three 6 mm bolts.
When Standalone GPS antenna is used, an additional VHF antenna

must also be connected
For detailed description of this antenna, see chapter 15.4.

Calculation of cable length/attenuation etc is described in chapter 8.2

Figure 8-7 GPS antenna connection

TR-8000 MkII Transponder

Содержание 103660









































































































Результаты поиска

Содержание 103660

Отзывы:

Похожие инструкции для 103660

Бренды по названию

Популярные бренды

jotron 103660, Руководство оператора и инструкция по установке

Результаты поиска

Содержание 103660

Отзывы:

Похожие инструкции для 103660

Бренды по названию

Популярные бренды