Johnson Controls YORK OPTIVIEW CONTROL CENTER Скачать руководство пользователя страница 57

Страница: 57 / 142

JOHNSON CONTROLS

SECTION 2 - OPTIVIEW OPERATION

FORM 160.10-O1

ISSUE DATE: 4/27/2018

Network) mode, or programmed locally at the control

center in local mode.

Pulldown Demand Time Left (Not Shown)

Displays the time remaining in the programmed

pulldown period. Only displayed if there is time re-

maining.

Operating Mode (Run / Stop)

This indicates the mode of operation for the chiller.

VSD Model

Access Level Required: SERVICE

Displays the horsepower configuration of the variable

speed drive control, as reported by the VSD to the Op-

tiView panel.

DC Bus Voltage

Displays the DC bus voltage as measured by the har-

monic filter.

OVERVIEW

This screen displays detailed information pertaining

to the IEEE-519 Harmonic Filter. This screen is only

available on the OptiView panel if the harmonic filter

is installed.

DISPLAY ONLY
Motor Run (LED)

Illuminates when the digital output from the controls is

commanding the motor to “RUN”.

(Motor Current) % Full Load Amps

Displays the motor current as a percentage of the Full

Load Amps (FLA) value. For the variable speed drive

this is the data returned by the VSD Logic board.

Current Limit Setpoint

Displays the current limit setpoint programmed by

the operator. This value could come from a 0-20mA,

4-20mA, 0-10VDC or 2-10VDC input in analog re-

mote mode, PWM signal in digital remote mode,

MicroGateway interface in ISN (Integrated Systems

HARMONIC FILTER DETAILS SCREEN 1

STYLE D VSD AND VSD WITH PART NUMBER 371-03789-xxx 503HP (60Hz) OR 419HP (50Hz)

00315VIP

FIGURE 21 -

HARMONIC FILTER DETAILS SCREEN 1

–

Содержание YORK OPTIVIEW CONTROL CENTER















































































































































Результаты поиска

Содержание YORK OPTIVIEW CONTROL CENTER

Отзывы:

Похожие инструкции для YORK OPTIVIEW CONTROL CENTER

Бренды по названию

Популярные бренды

Johnson Controls YORK OPTIVIEW CONTROL CENTER, Руководство по эксплуатации

Результаты поиска

Содержание YORK OPTIVIEW CONTROL CENTER

Отзывы:

Похожие инструкции для YORK OPTIVIEW CONTROL CENTER

Бренды по названию

Популярные бренды