Johnson Controls YORK OPTIVIEW CONTROL CENTER Скачать руководство пользователя страница 49

Страница: 49 / 142

JOHNSON CONTROLS

SECTION 2 - OPTIVIEW OPERATION

FORM 160.10-O1

ISSUE DATE: 4/27/2018

Pulldown Demand Time Left (Not Shown)

Displays the time remaining in the programmed

pulldown period. This value is only displayed if there

is time remaining.

Output Voltage

Displays the measured output voltage to the chiller mo-

tor.

Output Frequency

Displays the present output frequency to the motor.

Output Current – Phase A, B, C

Displays the phase current measured to the motor.

Input Power

Displays the total kilowatts measured by the VSD or

harmonic filter, if installed.

kW Hours

Displays the cumulative amount of kilowatts used over

time since the count was last reset.

OVERVIEW

This screen displays information pertaining to chillers

equipped with a Variable Speed Drive (VSD).

DISPLAY ONLY
Motor Run (LED)

Illuminates when the digital output from the controls is

commanding the motor to “RUN”.

(Motor Current) % Full Load Amps

Displays the motor current as a percentage of the Full

Load Amps (FLA) value.

Current Limit Setpoint

Displays the current limit setpoint programmed by

the operator. This value could come from a 0-20mA,

4-20 mA, 0-10VDC or 2-10VDC input in analog re-

mote mode, PWM signal in digital remote mode,

MicroGateway interface in ISN (Integrated Systems

Network) mode, or programmed locally at the control

center in local mode.

VARIABLE SPEED DRIVE SCREEN

LD10002

FIGURE 17 -

VSD SCREEN

Содержание YORK OPTIVIEW CONTROL CENTER















































































































































Результаты поиска

Содержание YORK OPTIVIEW CONTROL CENTER

Отзывы:

Похожие инструкции для YORK OPTIVIEW CONTROL CENTER

Бренды по названию

Популярные бренды

Johnson Controls YORK OPTIVIEW CONTROL CENTER, Руководство по эксплуатации

Результаты поиска

Содержание YORK OPTIVIEW CONTROL CENTER

Отзывы:

Похожие инструкции для YORK OPTIVIEW CONTROL CENTER

Бренды по названию

Популярные бренды