JetCat SPH5 Скачать руководство пользователя страница 49

Страница: 49 / 60

The Test Functions Menu

The Manual mode is no longer implemented. Instead, a new expanded set of test
functions are available from the

Test–Functions Menu

. To test the selected

component, press the

Change Value/Item

key. To change the fuel pump or glow plug

voltage when testing, while pressing the

Change Value/Item

key, press the

◄

- or

►

key. The following functions are available ->

Value

Explanation

Pump TestVolt

Opens fuel valve and runs the pump.
Default = 0.500 volts.

Note:

Can be used to prime the pump and fuel system. Make sure

the fuel line is disconnected from the turbine.

GlowPlug Power

Test and / or change glow plug voltage.
Default = 2.100 volts.

GasValve Test

Test starting gas valve.

FuelValve Test

Test fuel valve.

Temp
AD

Temperature value and offset.
Analog Converter value and offset

The LIMITs Menu

The LIMITs menu allows the operator to adjust the following parameters of the turbine,
within the allowable values, according to the performance requirements of a particular
model.

Value

Explanation

Minimum RPM

Turbine idle speed

Maximum RPM

Turbine maximum speed

LowBat Warning

Battery warning function, Enabled/Disabled
Default = Disabled (OFF)

GlowPlug Power

Glow plug voltage, The glow plug will glow with the selected
voltage when the

Change Value/Item

key is pressed.

Default = 2.100V

Gas Flow

Sets the amount of starting gas that will flow when the turbine is
started. The range is from 10 to 100% adjustable in 10%
increments.

Содержание SPH5




























































Результаты поиска

Содержание SPH5

Отзывы:

Похожие инструкции для SPH5

Бренды по названию

Популярные бренды

JetCat SPH5, Инструкция по эксплуатации

Результаты поиска

Содержание SPH5

Отзывы:

Похожие инструкции для SPH5

Бренды по названию

Популярные бренды