JetCat SPH5 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 60

background image

Turbine ignites,
but the start
process is
discontinued.

Air in fuel feed lines.

Fuel pump not running.

Starting gas tank nearly empty.

Air leaks in fuel system.
Examine all Festo fittings,
nipples, clunk, filter, etc.
Check for fuel filter clogs.

Test the pump in manual mode
(as soon as the red

Pump

running

LED illuminates, the

fuel pump must run!). See page
37.

Fill starting gas tank.

Starter unit slips,
makes noise.

Dust and oil sediment on the
compressor nut and O-ring.

Clean O-ring and compressor
nut periodically, with cotton
swab and solvent.

EGT giving erratic
temperature or
RPM readings.

Transmitter antenna too close
to the model.

Keep the antenna away from the
model. It may cause false
readings.

Turbine quits with
Watchdog Failure

Static discharge reset the ECU. Do not mount ECU directly to

the fiberglass body of the plane.
Use a plywood mount with a
layer of foam tape and Velcro
between the body and the ECU.
If the plane has a glossy finish
and the failure happened
directly after the wheels left the
ground, spray the tires with an
anti-static spray available from
electronic or hardware supply
stores.

Reason for Shut-Down

There are three ways to diagnose why the engine flamed out.

1. In the info menu the "LAST OFF-COND" variable will tell you why. For example,

low RPM, high temp, fail-safe etc.

This parameter is non-volatile and will be

available until the engine is run again.

2. With V4.0g and later ECU you can view the last 4 seconds of the flight before it

shut-down. This data is updated every 0.2 seconds. This allows you to see the
trend leading up to the shut-down. This mode is entered by pressing the "+" key
of the GSU while powering up the ECU. You can scroll through the data using
the (+ or -) keys and scroll forward and backward through time using the (info or
min/max) keys.

This parameter is non-volatile and will be available until the

engine is run again.

54

«
...
52
53
54
55
56
...
»

Содержание SPH5





























































Отзывы:

Нет отзывов

Похожие инструкции для SPH5

Бренд: Eurotronic Страницы: 4

Бренд: Chery Страницы: 55

Бренд: Hitachi Страницы: 41

Бренд: Hitachi Страницы: 1037

Бренд: Hitachi Страницы: 1104

Бренд: Volvo Penta Страницы: 116

Бренд: Toro Страницы: 37

Бренд: Fagor Страницы: 174

Бренд: Valach Страницы: 24

Бренд: Electro motive Страницы: 287

Бренд: WilTec Страницы: 6

Бренд: WilTec Страницы: 12

P10-70-SSC Series

Бренд: LinMot Страницы: 32

Бренд: LinMot Страницы: 32

PS01-37x120F-HP-SSC-R/ FC

Бренд: LinMot Страницы: 40

2232***BX4 series

Бренд: Faulhaber Страницы: 60

Бренд: Honda Страницы: 28

Бренд: Marine Power Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды