JetCat SPH5 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 60

background image

14

Checking of RPM sensor for the second stage turbine:

As soon as the sensor for the second stage turbine has been connected to the Exp connector on the
ECU it is ready to be tested.

is ready to be tested.

Connect the GSU with LED- Board and switch the radio on. You will see the voltage of the turbine
battery indicated on the lower left side.

Connect the GSU with LED- Board and switch the radio on. You will see the voltage of the turbine
battery indicated on the lower left side.

Rotate the fan rapidly and the display will switch to indicate the fans rpm. If you wiggle the fan blade
with the magnet in it above the sensor it will show a fan rpm reading. It is a good idea to check

BOTH

magnets are being detected by the sensor.

Rotate the fan rapidly and the display will switch to indicate the fans rpm. If you wiggle the fan blade
with the magnet in it above the sensor it will show a fan rpm reading. It is a good idea to check

BOTH

magnets are being detected by the sensor.

Attention: Please never run the engine under an unloaded condition. It should be installed and drive
the main rotor head with the blades.

The maximum rpm of the turbine engine can be set in the “Limits-Menu

Should the rpm sensor fail during flight, the rpm will be limited to the maximum rpm the engine has
had during that flight.

Turbine battery
voltage/fan rpm

«
...
12
13
14
15
16
...
»

Содержание SPH5





























































Отзывы:

Нет отзывов

Похожие инструкции для SPH5

Бренд: GAPOSA Страницы: 20

Бренд: DLE Страницы: 4

Бренд: Brother Страницы: 42

Бренд: Viessmann Страницы: 14

Dexxo Pro 1000 RTS

Бренд: SOMFY Страницы: 13

Elixo 500 230 V

Бренд: SOMFY Страницы: 44

Elixo 500 230 V

Бренд: SOMFY Страницы: 48

Бренд: BGS technic Страницы: 8

Бренд: O.S. engine Страницы: 13

MAX-15CV Series

Бренд: O.S. engine Страницы: 30

Бренд: Volvo Penta Страницы: 114

RolloTube S-line DuoFern

Бренд: RADEMACHER Страницы: 8

RolloTube Basis

Бренд: RADEMACHER Страницы: 60

Бренд: RADEMACHER Страницы: 64

Бренд: Hacker Страницы: 8

Бренд: Hacker Страницы: 8

Бренд: Hacker Страницы: 38

Бренд: O.S. engine Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды